Skip to content

ASoC: HKDK : max98090: Update master clock frequencies - #55

Merged
mdrjr merged 1 commit into
hardkernel:odroid-3.8.yfrom
abradianu:odroid-3.8.y
Jul 9, 2014
Merged

ASoC: HKDK : max98090: Update master clock frequencies#55
mdrjr merged 1 commit into
hardkernel:odroid-3.8.yfrom
abradianu:odroid-3.8.y

Conversation

@abradianu

Copy link
Copy Markdown

For sampling rates smaller than 39KHz the master clock is set outside
the 10MHz - 60MHz range accepted by the max98090 driver. Update the
master clock frequencies to match the max98090 requirements for all the
supported sampling rates.

Signed-off-by: Adrian Bradianu abradianu@gmail.com

For sampling rates smaller than 39KHz the master clock is set outside
the 10MHz - 60MHz range accepted by the max98090 driver. Update the
master clock frequencies to match the max98090 requirements for all the
supported sampling rates.
Signed-off-by: Adrian Bradianu <abradianu@gmail.com>
mdrjr added a commit that referenced this pull request Jul 9, 2014
ASoC: HKDK : max98090: Update master clock frequencies
@mdrjr
mdrjr merged commit d8638b6 into hardkernel:odroid-3.8.yJul 9, 2014
@mdrjr

mdrjr commented Jul 9, 2014

Copy link
Copy Markdown
Collaborator

Once again. Thank you so much :) Merged!

mdrjr pushed a commit that referenced this pull request Aug 5, 2014
commit 2b4fbf0 upstream.
Add pipe_lock/unlock for splice_write to avoid oops by following competition:
(1) An application gets fds of a trace buffer, virtio-serial, pipe.
(2) The application does fork()
(3) The processes execute splice_read(trace buffer) and
splice_write(virtio-serial) via same pipe.
<parent> <child>
get fds of a trace buffer,
virtio-serial, pipe
|
fork()----------create--------+
| |
splice(read) | ---+
splice(write) | +-- no competition
| splice(read) |
| splice(write) ---+
| |
splice(read) |
splice(write) splice(read) ------ competition
| splice(write)
Two processes share a pipe_inode_info structure. If the child execute
splice(read) when the parent tries to execute splice(write), the
structure can be broken. Existing virtio-serial driver does not get
lock for the structure in splice_write, so this competition will induce
oops.
<oops messages>
BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
IP: [<ffffffff811a6b5f>] splice_from_pipe_feed+0x6f/0x130
PGD 7223e067 PUD 72391067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in: lockd bnep bluetooth rfkill sunrpc ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_page_alloc snd_timer snd soundcore pcspkr virtio_net virtio_balloon i2c_piix4 i2c_core microcode uinput floppy
CPU: 0 PID: 1072 Comm: compete-test Not tainted 3.10.0ws+ #55
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
task: ffff880071b98000 ti: ffff88007b55e000 task.ti: ffff88007b55e000
RIP: 0010:[<ffffffff811a6b5f>] [<ffffffff811a6b5f>] splice_from_pipe_feed+0x6f/0x130
RSP: 0018:ffff88007b55fd78 EFLAGS: 00010287
RAX: 0000000000000000 RBX: ffff88007b55fe20 RCX: 0000000000000000
RDX: 0000000000001000 RSI: ffff88007a95ba30 RDI: ffff880036f9e6c0
RBP: ffff88007b55fda8 R08: 00000000000006ec R09: ffff880077626708
R10: 0000000000000003 R11: ffffffff8139ca59 R12: ffff88007a95ba30
R13: 0000000000000000 R14: ffffffff8139dd00 R15: ffff880036f9e6c0
FS: 00007f2e2e3a0740(0000) GS:ffff88007fc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000018 CR3: 0000000071bd1000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
ffffffff8139ca59 ffff88007b55fe20 ffff880036f9e6c0 ffffffff8139dd00
ffff8800776266c0 ffff880077626708 ffff88007b55fde8 ffffffff811a6e8e
ffff88007b55fde8 ffffffff8139ca59 ffff880036f9e6c0 ffff88007b55fe20
Call Trace:
[<ffffffff8139ca59>] ? alloc_buf.isra.13+0x39/0xb0
[<ffffffff8139dd00>] ? virtcons_restore+0x100/0x100
[<ffffffff811a6e8e>] __splice_from_pipe+0x7e/0x90
[<ffffffff8139ca59>] ? alloc_buf.isra.13+0x39/0xb0
[<ffffffff8139d739>] port_fops_splice_write+0xe9/0x140
[<ffffffff8127a3f4>] ? selinux_file_permission+0xc4/0x120
[<ffffffff8139d650>] ? wait_port_writable+0x1b0/0x1b0
[<ffffffff811a6fe0>] do_splice_from+0xa0/0x110
[<ffffffff811a951f>] SyS_splice+0x5ff/0x6b0
[<ffffffff8161facf>] tracesys+0xdd/0xe2
Code: 49 8b 87 80 00 00 00 4c 8d 24 d0 8b 53 04 41 8b 44 24 0c 4d 8b 6c 24 10 39 d0 89 03 76 02 89 13 49 8b 44 24 10 4c 89 e6 4c 89 ff <ff> 50 18 85 c0 0f 85 aa 00 00 00 48 89 da 4c 89 e6 4c 89 ff 41
RIP [<ffffffff811a6b5f>] splice_from_pipe_feed+0x6f/0x130
RSP <ffff88007b55fd78>
CR2: 0000000000000018
---[ end trace 24572beb7764de59 ]---
V2: Fix a locking problem for error
V3: Add Reviewed-by lines and stable@ line in sign-off area
Signed-off-by: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Amit Shah <amit.shah@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmole pushed a commit to Dmole/linux that referenced this pull request Oct 6, 2016
While the driver is probing the adapter, an error may occur before the
netdev structure is allocated and attached to pci_dev. In this case,
not only netdev isn't available, but the tg3 private structure is also
not available as it is just math from the NULL pointer, so dereferences
must be skipped.
The following trace is seen when the error is triggered:
[1.402247] Unable to handle kernel paging request for data at address 0x00001a99
[1.402410] Faulting instruction address: 0xc0000000007e33f8
[1.402450] Oops: Kernel access of bad area, sig: 11 [hardkernel#1]
[1.402481] SMP NR_CPUS=2048 NUMA PowerNV
[1.402513] Modules linked in:
[1.402545] CPU: 0 PID: 651 Comm: eehd Not tainted 4.4.0-36-generic hardkernel#55-Ubuntu
[1.402591] task: c000001fe4e42a20 ti: c000001fe4e88000 task.ti: c000001fe4e88000
[1.402742] NIP: c0000000007e33f8 LR: c0000000007e3164 CTR: c000000000595ea0
[1.402787] REGS: c000001fe4e8b790 TRAP: 0300 Not tainted (4.4.0-36-generic)
[1.402832] MSR: 9000000100009033 <SF,HV,EE,ME,IR,DR,RI,LE> CR: 28000422 XER: 20000000
[1.403058] CFAR: c000000000008468 DAR: 0000000000001a99 DSISR: 42000000 SOFTE: 1
GPR00: c0000000007e3164 c000001fe4e8ba10 c0000000015c5e00 0000000000000000
GPR04: 0000000000000001 0000000000000000 0000000000000039 0000000000000299
GPR08: 0000000000000000 0000000000000001 c000001fe4e88000 0000000000000006
GPR12: 0000000000000000 c00000000fb40000 c0000000000e6558 c000003ca1bffd00
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 c000000000d52768
GPR24: c000000000d52740 0000000000000100 c000003ca1b52000 0000000000000002
GPR28: 0000000000000900 0000000000000000 c00000000152a0c0 c000003ca1b52000
[1.404226] NIP [c0000000007e33f8] tg3_io_error_detected+0x308/0x340
[1.404265] LR [c0000000007e3164] tg3_io_error_detected+0x74/0x340
This patch avoids the NULL pointer dereference by moving the access after
the netdev NULL pointer check on tg3_io_error_detected(). Also, we add a
check for netdev being NULL on tg3_io_resume() [suggested by Michael Chan].
Fixes: 0486a06 ("tg3: prevent ifup/ifdown during PCI error recovery")
Fixes: dfc8f37 ("net/tg3: Release IRQs on permanent error")
Tested-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmole pushed a commit to Dmole/linux that referenced this pull request Oct 6, 2016
…age_cache_page()
Antonio reports the following crash when using fuse under memory pressure:
kernel BUG at /build/linux-a2WvEb/linux-4.4.0/mm/workingset.c:346!
invalid opcode: 0000 [hardkernel#1] SMP
Modules linked in: all of them
CPU: 2 PID: 63 Comm: kswapd0 Not tainted 4.4.0-36-generic hardkernel#55-Ubuntu
Hardware name: System manufacturer System Product Name/P8H67-M PRO, BIOS 3904 04/27/2013
task: ffff88040cae6040 ti: ffff880407488000 task.ti: ffff880407488000
RIP: shadow_lru_isolate+0x181/0x190
Call Trace:
__list_lru_walk_one.isra.3+0x8f/0x130
list_lru_walk_one+0x23/0x30
scan_shadow_nodes+0x34/0x50
shrink_slab.part.40+0x1ed/0x3d0
shrink_zone+0x2ca/0x2e0
kswapd+0x51e/0x990
kthread+0xd8/0xf0
ret_from_fork+0x3f/0x70
which corresponds to the following sanity check in the shadow node
tracking:
BUG_ON(node->count & RADIX_TREE_COUNT_MASK);
The workingset code tracks radix tree nodes that exclusively contain
shadow entries of evicted pages in them, and this (somewhat obscure)
line checks whether there are real pages left that would interfere with
reclaim of the radix tree node under memory pressure.
While discussing ways how fuse might sneak pages into the radix tree
past the workingset code, Miklos pointed to replace_page_cache_page(),
and indeed there is a problem there: it properly accounts for the old
page being removed - __delete_from_page_cache() does that - but then
does a raw raw radix_tree_insert(), not accounting for the replacement
page. Eventually the page count bits in node->count underflow while
leaving the node incorrectly linked to the shadow node LRU.
To address this, make sure replace_page_cache_page() uses the tracked
page insertion code, page_cache_tree_insert(). This fixes the page
accounting and makes sure page-containing nodes are properly unlinked
from the shadow node LRU again.
Also, make the sanity checks a bit less obscure by using the helpers for
checking the number of pages and shadows in a radix tree node.
Fixes: 449dd69 ("mm: keep page cache radix tree nodes in check")
Link: http://lkml.kernel.org/r/20160919155822.29498-1-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Antonio SJ Musumeci <trapexit@spawn.link>
Debugged-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: <stable@vger.kernel.org>	[3.15+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dmole pushed a commit to Dmole/linux that referenced this pull request Oct 29, 2016
…age_cache_page()
commit 22f2ac5 upstream.
Antonio reports the following crash when using fuse under memory pressure:
kernel BUG at /build/linux-a2WvEb/linux-4.4.0/mm/workingset.c:346!
invalid opcode: 0000 [hardkernel#1] SMP
Modules linked in: all of them
CPU: 2 PID: 63 Comm: kswapd0 Not tainted 4.4.0-36-generic hardkernel#55-Ubuntu
Hardware name: System manufacturer System Product Name/P8H67-M PRO, BIOS 3904 04/27/2013
task: ffff88040cae6040 ti: ffff880407488000 task.ti: ffff880407488000
RIP: shadow_lru_isolate+0x181/0x190
Call Trace:
__list_lru_walk_one.isra.3+0x8f/0x130
list_lru_walk_one+0x23/0x30
scan_shadow_nodes+0x34/0x50
shrink_slab.part.40+0x1ed/0x3d0
shrink_zone+0x2ca/0x2e0
kswapd+0x51e/0x990
kthread+0xd8/0xf0
ret_from_fork+0x3f/0x70
which corresponds to the following sanity check in the shadow node
tracking:
BUG_ON(node->count & RADIX_TREE_COUNT_MASK);
The workingset code tracks radix tree nodes that exclusively contain
shadow entries of evicted pages in them, and this (somewhat obscure)
line checks whether there are real pages left that would interfere with
reclaim of the radix tree node under memory pressure.
While discussing ways how fuse might sneak pages into the radix tree
past the workingset code, Miklos pointed to replace_page_cache_page(),
and indeed there is a problem there: it properly accounts for the old
page being removed - __delete_from_page_cache() does that - but then
does a raw raw radix_tree_insert(), not accounting for the replacement
page. Eventually the page count bits in node->count underflow while
leaving the node incorrectly linked to the shadow node LRU.
To address this, make sure replace_page_cache_page() uses the tracked
page insertion code, page_cache_tree_insert(). This fixes the page
accounting and makes sure page-containing nodes are properly unlinked
from the shadow node LRU again.
Also, make the sanity checks a bit less obscure by using the helpers for
checking the number of pages and shadows in a radix tree node.
[mhocko@suse.com: backport for 4.4]
Fixes: 449dd69 ("mm: keep page cache radix tree nodes in check")
Link: http://lkml.kernel.org/r/20160919155822.29498-1-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Antonio SJ Musumeci <trapexit@spawn.link>
Debugged-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmole pushed a commit to Dmole/linux that referenced this pull request Nov 15, 2016
[ Upstream commit 1b0ff89 ]
While the driver is probing the adapter, an error may occur before the
netdev structure is allocated and attached to pci_dev. In this case,
not only netdev isn't available, but the tg3 private structure is also
not available as it is just math from the NULL pointer, so dereferences
must be skipped.
The following trace is seen when the error is triggered:
[1.402247] Unable to handle kernel paging request for data at address 0x00001a99
[1.402410] Faulting instruction address: 0xc0000000007e33f8
[1.402450] Oops: Kernel access of bad area, sig: 11 [hardkernel#1]
[1.402481] SMP NR_CPUS=2048 NUMA PowerNV
[1.402513] Modules linked in:
[1.402545] CPU: 0 PID: 651 Comm: eehd Not tainted 4.4.0-36-generic hardkernel#55-Ubuntu
[1.402591] task: c000001fe4e42a20 ti: c000001fe4e88000 task.ti: c000001fe4e88000
[1.402742] NIP: c0000000007e33f8 LR: c0000000007e3164 CTR: c000000000595ea0
[1.402787] REGS: c000001fe4e8b790 TRAP: 0300 Not tainted (4.4.0-36-generic)
[1.402832] MSR: 9000000100009033 <SF,HV,EE,ME,IR,DR,RI,LE> CR: 28000422 XER: 20000000
[1.403058] CFAR: c000000000008468 DAR: 0000000000001a99 DSISR: 42000000 SOFTE: 1
GPR00: c0000000007e3164 c000001fe4e8ba10 c0000000015c5e00 0000000000000000
GPR04: 0000000000000001 0000000000000000 0000000000000039 0000000000000299
GPR08: 0000000000000000 0000000000000001 c000001fe4e88000 0000000000000006
GPR12: 0000000000000000 c00000000fb40000 c0000000000e6558 c000003ca1bffd00
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 c000000000d52768
GPR24: c000000000d52740 0000000000000100 c000003ca1b52000 0000000000000002
GPR28: 0000000000000900 0000000000000000 c00000000152a0c0 c000003ca1b52000
[1.404226] NIP [c0000000007e33f8] tg3_io_error_detected+0x308/0x340
[1.404265] LR [c0000000007e3164] tg3_io_error_detected+0x74/0x340
This patch avoids the NULL pointer dereference by moving the access after
the netdev NULL pointer check on tg3_io_error_detected(). Also, we add a
check for netdev being NULL on tg3_io_resume() [suggested by Michael Chan].
Fixes: 0486a06 ("tg3: prevent ifup/ifdown during PCI error recovery")
Fixes: dfc8f37 ("net/tg3: Release IRQs on permanent error")
Tested-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
peak3d pushed a commit to peak3d/linux that referenced this pull request Mar 3, 2018
test_bit will access with unsigned long, which cause this bug.
Workaround by enlarge free_nid_bitmap.
BUG: KASAN: slab-out-of-bounds in update_free_nid_bitmap+0x98/0x16c
Read of size 8 at addr ffffffc06275c9ff by task init/195
CPU: 3 PID: 195 Comm: init Not tainted 4.4.114 hardkernel#55
Hardware name: Rockchip rk3326 evb board (DT)
Call trace:
dump_backtrace+0x0/0x244
show_stack+0x14/0x1c
dump_stack+0xa4/0xcc
print_address_description+0xa4/0x308
kasan_report+0x258/0x29c
__asan_load8+0x78/0x80
update_free_nid_bitmap+0x98/0x16c
build_node_manager+0x884/0x950
f2fs_fill_super+0x14bc/0x1ca8
mount_bdev+0x174/0x208
f2fs_mount+0x14/0x1c
mount_fs+0xbc/0x1b0
vfs_kern_mount+0xbc/0x1c8
do_mount+0xcf0/0xe68
SyS_mount+0x94/0xe0
el0_svc_naked+0x24/0x28
Change-Id: I9167447ded0a8c2da1b80cdc671615c9108c02be
Signed-off-by: Tao Huang <huangtao@rock-chips.com>
mdrjr pushed a commit that referenced this pull request Oct 23, 2018
[ Upstream commit 7acfda5 ]
When element of verdict map is deleted, the delete routine should
release chain. however, flush element of verdict map routine doesn't
release chain.
test commands:
%nft add table ip filter
%nft add chain ip filter c1
%nft add map ip filter map1 { type ipv4_addr : verdict \; }
%nft add element ip filter map1 { 1 : jump c1 }
%nft flush map ip filter map1
%nft flush ruleset
splat looks like:
[ 4895.170899] kernel BUG at net/netfilter/nf_tables_api.c:1415!
[ 4895.178114] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 4895.178880] CPU: 0 PID: 1670 Comm: nft Not tainted 4.18.0+ #55
[ 4895.178880] RIP: 0010:nf_tables_chain_destroy.isra.28+0x39/0x220 [nf_tables]
[ 4895.178880] Code: fc ff df 53 48 89 fb 48 83 c7 50 48 89 fa 48 c1 ea 03 0f b6 04 02 84 c0 74 09 3c 03 7f 05 e8 3e 4c 25 e1 8b 43 50 85 c0 74 02 <0f> 0b 48 89 da 48 b8 00 00 00 00 00 fc ff df 48 c1 ea 03 80 3c 02
[ 4895.228342] RSP: 0018:ffff88010b98f4c0 EFLAGS: 00010202
[ 4895.234841] RAX: 0000000000000001 RBX: ffff8801131c6968 RCX: ffff8801146585b0
[ 4895.234841] RDX: 1ffff10022638d37 RSI: ffff8801191a9348 RDI: ffff8801131c69b8
[ 4895.234841] RBP: ffff8801146585a8 R08: 1ffff1002323526a R09: 0000000000000000
[ 4895.234841] R10: 0000000000000000 R11: 0000000000000000 R12: dead000000000200
[ 4895.234841] R13: dead000000000100 R14: ffffffffa3638af8 R15: dffffc0000000000
[ 4895.234841] FS: 00007f6d188e6700(0000) GS:ffff88011b600000(0000) knlGS:0000000000000000
[ 4895.234841] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 4895.234841] CR2: 00007ffe72b8df88 CR3: 000000010e2d4000 CR4: 00000000001006f0
[ 4895.234841] Call Trace:
[ 4895.234841] nf_tables_commit+0x2704/0x2c70 [nf_tables]
[ 4895.234841] ? nfnetlink_rcv_batch+0xa4f/0x11b0 [nfnetlink]
[ 4895.234841] ? nf_tables_setelem_notify.constprop.48+0x1a0/0x1a0 [nf_tables]
[ 4895.323824] ? __lock_is_held+0x9d/0x130
[ 4895.323824] ? kasan_unpoison_shadow+0x30/0x40
[ 4895.333299] ? kasan_kmalloc+0xa9/0xc0
[ 4895.333299] ? kmem_cache_alloc_trace+0x2c0/0x310
[ 4895.333299] ? nfnetlink_rcv_batch+0xa4f/0x11b0 [nfnetlink]
[ 4895.333299] nfnetlink_rcv_batch+0xdb9/0x11b0 [nfnetlink]
[ 4895.333299] ? debug_show_all_locks+0x290/0x290
[ 4895.333299] ? nfnetlink_net_init+0x150/0x150 [nfnetlink]
[ 4895.333299] ? sched_clock_cpu+0xe5/0x170
[ 4895.333299] ? sched_clock_local+0xff/0x130
[ 4895.333299] ? sched_clock_cpu+0xe5/0x170
[ 4895.333299] ? find_held_lock+0x39/0x1b0
[ 4895.333299] ? sched_clock_local+0xff/0x130
[ 4895.333299] ? memset+0x1f/0x40
[ 4895.333299] ? nla_parse+0x33/0x260
[ 4895.333299] ? ns_capable_common+0x6e/0x110
[ 4895.333299] nfnetlink_rcv+0x2c0/0x310 [nfnetlink]
[ ... ]
Fixes: 5910544 ("netfilter: nf_tables: revisit chain/object refcounting from elements")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mdrjr pushed a commit that referenced this pull request Apr 16, 2019
[ Upstream commit 4117992 ]
KASAN does not play well with the page poisoning (CONFIG_PAGE_POISONING).
It triggers false positives in the allocation path:
BUG: KASAN: use-after-free in memchr_inv+0x2ea/0x330
Read of size 8 at addr ffff88881f800000 by task swapper/0
CPU: 0 PID: 0 Comm: swapper Not tainted 5.0.0-rc1+ #54
Call Trace:
dump_stack+0xe0/0x19a
print_address_description.cold.2+0x9/0x28b
kasan_report.cold.3+0x7a/0xb5
__asan_report_load8_noabort+0x19/0x20
memchr_inv+0x2ea/0x330
kernel_poison_pages+0x103/0x3d5
get_page_from_freelist+0x15e7/0x4d90
because KASAN has not yet unpoisoned the shadow page for allocation
before it checks memchr_inv() but only found a stale poison pattern.
Also, false positives in free path,
BUG: KASAN: slab-out-of-bounds in kernel_poison_pages+0x29e/0x3d5
Write of size 4096 at addr ffff8888112cc000 by task swapper/0/1
CPU: 5 PID: 1 Comm: swapper/0 Not tainted 5.0.0-rc1+ #55
Call Trace:
dump_stack+0xe0/0x19a
print_address_description.cold.2+0x9/0x28b
kasan_report.cold.3+0x7a/0xb5
check_memory_region+0x22d/0x250
memset+0x28/0x40
kernel_poison_pages+0x29e/0x3d5
__free_pages_ok+0x75f/0x13e0
due to KASAN adds poisoned redzones around slab objects, but the page
poisoning needs to poison the whole page.
Link: http://lkml.kernel.org/r/20190114233405.67843-1-cai@lca.pw
Signed-off-by: Qian Cai <cai@lca.pw>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
mdrjr pushed a commit that referenced this pull request Sep 15, 2020
commit 205d300 upstream.
We have a number of "uart.port->desc.lock vs desc.lock->uart.port"
lockdep reports coming from 8250 driver; this causes a bit of trouble
to people, so let's fix it.
The problem is reverse lock order in two different call paths:
chain #1:
serial8250_do_startup()
spin_lock_irqsave(&port->lock);
disable_irq_nosync(port->irq);
raw_spin_lock_irqsave(&desc->lock)
chain #2:
__report_bad_irq()
raw_spin_lock_irqsave(&desc->lock)
for_each_action_of_desc()
printk()
spin_lock_irqsave(&port->lock);
Fix this by changing the order of locks in serial8250_do_startup():
do disable_irq_nosync() first, which grabs desc->lock, and grab
uart->port after that, so that chain #1 and chain #2 have same lock
order.
Full lockdep splat:
======================================================
WARNING: possible circular locking dependency detected
5.4.39 #55 Not tainted
======================================================
swapper/0/0 is trying to acquire lock:
ffffffffab65b6c0 (console_owner){-...}, at: console_lock_spinning_enable+0x31/0x57
but task is already holding lock:
ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&irq_desc_lock_class){-.-.}:
_raw_spin_lock_irqsave+0x61/0x8d
__irq_get_desc_lock+0x65/0x89
__disable_irq_nosync+0x3b/0x93
serial8250_do_startup+0x451/0x75c
uart_startup+0x1b4/0x2ff
uart_port_activate+0x73/0xa0
tty_port_open+0xae/0x10a
uart_open+0x1b/0x26
tty_open+0x24d/0x3a0
chrdev_open+0xd5/0x1cc
do_dentry_open+0x299/0x3c8
path_openat+0x434/0x1100
do_filp_open+0x9b/0x10a
do_sys_open+0x15f/0x3d7
kernel_init_freeable+0x157/0x1dd
kernel_init+0xe/0x105
ret_from_fork+0x27/0x50
-> #1 (&port_lock_key){-.-.}:
_raw_spin_lock_irqsave+0x61/0x8d
serial8250_console_write+0xa7/0x2a0
console_unlock+0x3b7/0x528
vprintk_emit+0x111/0x17f
printk+0x59/0x73
register_console+0x336/0x3a4
uart_add_one_port+0x51b/0x5be
serial8250_register_8250_port+0x454/0x55e
dw8250_probe+0x4dc/0x5b9
platform_drv_probe+0x67/0x8b
really_probe+0x14a/0x422
driver_probe_device+0x66/0x130
device_driver_attach+0x42/0x5b
__driver_attach+0xca/0x139
bus_for_each_dev+0x97/0xc9
bus_add_driver+0x12b/0x228
driver_register+0x64/0xed
do_one_initcall+0x20c/0x4a6
do_initcall_level+0xb5/0xc5
do_basic_setup+0x4c/0x58
kernel_init_freeable+0x13f/0x1dd
kernel_init+0xe/0x105
ret_from_fork+0x27/0x50
-> #0 (console_owner){-...}:
__lock_acquire+0x118d/0x2714
lock_acquire+0x203/0x258
console_lock_spinning_enable+0x51/0x57
console_unlock+0x25d/0x528
vprintk_emit+0x111/0x17f
printk+0x59/0x73
__report_bad_irq+0xa3/0xba
note_interrupt+0x19a/0x1d6
handle_irq_event_percpu+0x57/0x79
handle_irq_event+0x36/0x55
handle_fasteoi_irq+0xc2/0x18a
do_IRQ+0xb3/0x157
ret_from_intr+0x0/0x1d
cpuidle_enter_state+0x12f/0x1fd
cpuidle_enter+0x2e/0x3d
do_idle+0x1ce/0x2ce
cpu_startup_entry+0x1d/0x1f
start_kernel+0x406/0x46a
secondary_startup_64+0xa4/0xb0
other info that might help us debug this:
Chain exists of:
console_owner --> &port_lock_key --> &irq_desc_lock_class
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&irq_desc_lock_class);
lock(&port_lock_key);
lock(&irq_desc_lock_class);
lock(console_owner);
*** DEADLOCK ***
2 locks held by swapper/0/0:
#0: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba
#1: ffffffffab65b5c0 (console_lock){+.+.}, at: console_trylock_spinning+0x20/0x181
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.39 #55
Hardware name: XXXXXX
Call Trace:
<IRQ>
dump_stack+0xbf/0x133
? print_circular_bug+0xd6/0xe9
check_noncircular+0x1b9/0x1c3
__lock_acquire+0x118d/0x2714
lock_acquire+0x203/0x258
? console_lock_spinning_enable+0x31/0x57
console_lock_spinning_enable+0x51/0x57
? console_lock_spinning_enable+0x31/0x57
console_unlock+0x25d/0x528
? console_trylock+0x18/0x4e
vprintk_emit+0x111/0x17f
? lock_acquire+0x203/0x258
printk+0x59/0x73
__report_bad_irq+0xa3/0xba
note_interrupt+0x19a/0x1d6
handle_irq_event_percpu+0x57/0x79
handle_irq_event+0x36/0x55
handle_fasteoi_irq+0xc2/0x18a
do_IRQ+0xb3/0x157
common_interrupt+0xf/0xf
</IRQ>
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Fixes: 768aec0 ("serial: 8250: fix shared interrupts issues with SMP and RT kernels")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Raul Rangel <rrangel@google.com>
BugLink: https://bugs.chromium.org/p/chromium/issues/detail?id=1114800
Link: https://lore.kernel.org/lkml/CAHQZ30BnfX+gxjPm1DUd5psOTqbyDh4EJE=2=VAMW_VDafctkA@mail.gmail.com/T/#u
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200817022646.1484638-1-sergey.senozhatsky@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mdrjr pushed a commit that referenced this pull request Sep 15, 2020
commit 205d300 upstream.
We have a number of "uart.port->desc.lock vs desc.lock->uart.port"
lockdep reports coming from 8250 driver; this causes a bit of trouble
to people, so let's fix it.
The problem is reverse lock order in two different call paths:
chain #1:
serial8250_do_startup()
spin_lock_irqsave(&port->lock);
disable_irq_nosync(port->irq);
raw_spin_lock_irqsave(&desc->lock)
chain #2:
__report_bad_irq()
raw_spin_lock_irqsave(&desc->lock)
for_each_action_of_desc()
printk()
spin_lock_irqsave(&port->lock);
Fix this by changing the order of locks in serial8250_do_startup():
do disable_irq_nosync() first, which grabs desc->lock, and grab
uart->port after that, so that chain #1 and chain #2 have same lock
order.
Full lockdep splat:
======================================================
WARNING: possible circular locking dependency detected
5.4.39 #55 Not tainted
======================================================
swapper/0/0 is trying to acquire lock:
ffffffffab65b6c0 (console_owner){-...}, at: console_lock_spinning_enable+0x31/0x57
but task is already holding lock:
ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&irq_desc_lock_class){-.-.}:
_raw_spin_lock_irqsave+0x61/0x8d
__irq_get_desc_lock+0x65/0x89
__disable_irq_nosync+0x3b/0x93
serial8250_do_startup+0x451/0x75c
uart_startup+0x1b4/0x2ff
uart_port_activate+0x73/0xa0
tty_port_open+0xae/0x10a
uart_open+0x1b/0x26
tty_open+0x24d/0x3a0
chrdev_open+0xd5/0x1cc
do_dentry_open+0x299/0x3c8
path_openat+0x434/0x1100
do_filp_open+0x9b/0x10a
do_sys_open+0x15f/0x3d7
kernel_init_freeable+0x157/0x1dd
kernel_init+0xe/0x105
ret_from_fork+0x27/0x50
-> #1 (&port_lock_key){-.-.}:
_raw_spin_lock_irqsave+0x61/0x8d
serial8250_console_write+0xa7/0x2a0
console_unlock+0x3b7/0x528
vprintk_emit+0x111/0x17f
printk+0x59/0x73
register_console+0x336/0x3a4
uart_add_one_port+0x51b/0x5be
serial8250_register_8250_port+0x454/0x55e
dw8250_probe+0x4dc/0x5b9
platform_drv_probe+0x67/0x8b
really_probe+0x14a/0x422
driver_probe_device+0x66/0x130
device_driver_attach+0x42/0x5b
__driver_attach+0xca/0x139
bus_for_each_dev+0x97/0xc9
bus_add_driver+0x12b/0x228
driver_register+0x64/0xed
do_one_initcall+0x20c/0x4a6
do_initcall_level+0xb5/0xc5
do_basic_setup+0x4c/0x58
kernel_init_freeable+0x13f/0x1dd
kernel_init+0xe/0x105
ret_from_fork+0x27/0x50
-> #0 (console_owner){-...}:
__lock_acquire+0x118d/0x2714
lock_acquire+0x203/0x258
console_lock_spinning_enable+0x51/0x57
console_unlock+0x25d/0x528
vprintk_emit+0x111/0x17f
printk+0x59/0x73
__report_bad_irq+0xa3/0xba
note_interrupt+0x19a/0x1d6
handle_irq_event_percpu+0x57/0x79
handle_irq_event+0x36/0x55
handle_fasteoi_irq+0xc2/0x18a
do_IRQ+0xb3/0x157
ret_from_intr+0x0/0x1d
cpuidle_enter_state+0x12f/0x1fd
cpuidle_enter+0x2e/0x3d
do_idle+0x1ce/0x2ce
cpu_startup_entry+0x1d/0x1f
start_kernel+0x406/0x46a
secondary_startup_64+0xa4/0xb0
other info that might help us debug this:
Chain exists of:
console_owner --> &port_lock_key --> &irq_desc_lock_class
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&irq_desc_lock_class);
lock(&port_lock_key);
lock(&irq_desc_lock_class);
lock(console_owner);
*** DEADLOCK ***
2 locks held by swapper/0/0:
#0: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba
#1: ffffffffab65b5c0 (console_lock){+.+.}, at: console_trylock_spinning+0x20/0x181
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.39 #55
Hardware name: XXXXXX
Call Trace:
<IRQ>
dump_stack+0xbf/0x133
? print_circular_bug+0xd6/0xe9
check_noncircular+0x1b9/0x1c3
__lock_acquire+0x118d/0x2714
lock_acquire+0x203/0x258
? console_lock_spinning_enable+0x31/0x57
console_lock_spinning_enable+0x51/0x57
? console_lock_spinning_enable+0x31/0x57
console_unlock+0x25d/0x528
? console_trylock+0x18/0x4e
vprintk_emit+0x111/0x17f
? lock_acquire+0x203/0x258
printk+0x59/0x73
__report_bad_irq+0xa3/0xba
note_interrupt+0x19a/0x1d6
handle_irq_event_percpu+0x57/0x79
handle_irq_event+0x36/0x55
handle_fasteoi_irq+0xc2/0x18a
do_IRQ+0xb3/0x157
common_interrupt+0xf/0xf
</IRQ>
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Fixes: 768aec0 ("serial: 8250: fix shared interrupts issues with SMP and RT kernels")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Raul Rangel <rrangel@google.com>
BugLink: https://bugs.chromium.org/p/chromium/issues/detail?id=1114800
Link: https://lore.kernel.org/lkml/CAHQZ30BnfX+gxjPm1DUd5psOTqbyDh4EJE=2=VAMW_VDafctkA@mail.gmail.com/T/#u
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200817022646.1484638-1-sergey.senozhatsky@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
paralin pushed a commit to paralin/linux that referenced this pull request Sep 22, 2020
commit 205d300 upstream.
We have a number of "uart.port->desc.lock vs desc.lock->uart.port"
lockdep reports coming from 8250 driver; this causes a bit of trouble
to people, so let's fix it.
The problem is reverse lock order in two different call paths:
chain hardkernel#1:
serial8250_do_startup()
spin_lock_irqsave(&port->lock);
disable_irq_nosync(port->irq);
raw_spin_lock_irqsave(&desc->lock)
chain hardkernel#2:
__report_bad_irq()
raw_spin_lock_irqsave(&desc->lock)
for_each_action_of_desc()
printk()
spin_lock_irqsave(&port->lock);
Fix this by changing the order of locks in serial8250_do_startup():
do disable_irq_nosync() first, which grabs desc->lock, and grab
uart->port after that, so that chain hardkernel#1 and chain hardkernel#2 have same lock
order.
Full lockdep splat:
======================================================
WARNING: possible circular locking dependency detected
5.4.39 hardkernel#55 Not tainted
======================================================
swapper/0/0 is trying to acquire lock:
ffffffffab65b6c0 (console_owner){-...}, at: console_lock_spinning_enable+0x31/0x57
but task is already holding lock:
ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> hardkernel#2 (&irq_desc_lock_class){-.-.}:
_raw_spin_lock_irqsave+0x61/0x8d
__irq_get_desc_lock+0x65/0x89
__disable_irq_nosync+0x3b/0x93
serial8250_do_startup+0x451/0x75c
uart_startup+0x1b4/0x2ff
uart_port_activate+0x73/0xa0
tty_port_open+0xae/0x10a
uart_open+0x1b/0x26
tty_open+0x24d/0x3a0
chrdev_open+0xd5/0x1cc
do_dentry_open+0x299/0x3c8
path_openat+0x434/0x1100
do_filp_open+0x9b/0x10a
do_sys_open+0x15f/0x3d7
kernel_init_freeable+0x157/0x1dd
kernel_init+0xe/0x105
ret_from_fork+0x27/0x50
-> hardkernel#1 (&port_lock_key){-.-.}:
_raw_spin_lock_irqsave+0x61/0x8d
serial8250_console_write+0xa7/0x2a0
console_unlock+0x3b7/0x528
vprintk_emit+0x111/0x17f
printk+0x59/0x73
register_console+0x336/0x3a4
uart_add_one_port+0x51b/0x5be
serial8250_register_8250_port+0x454/0x55e
dw8250_probe+0x4dc/0x5b9
platform_drv_probe+0x67/0x8b
really_probe+0x14a/0x422
driver_probe_device+0x66/0x130
device_driver_attach+0x42/0x5b
__driver_attach+0xca/0x139
bus_for_each_dev+0x97/0xc9
bus_add_driver+0x12b/0x228
driver_register+0x64/0xed
do_one_initcall+0x20c/0x4a6
do_initcall_level+0xb5/0xc5
do_basic_setup+0x4c/0x58
kernel_init_freeable+0x13f/0x1dd
kernel_init+0xe/0x105
ret_from_fork+0x27/0x50
-> #0 (console_owner){-...}:
__lock_acquire+0x118d/0x2714
lock_acquire+0x203/0x258
console_lock_spinning_enable+0x51/0x57
console_unlock+0x25d/0x528
vprintk_emit+0x111/0x17f
printk+0x59/0x73
__report_bad_irq+0xa3/0xba
note_interrupt+0x19a/0x1d6
handle_irq_event_percpu+0x57/0x79
handle_irq_event+0x36/0x55
handle_fasteoi_irq+0xc2/0x18a
do_IRQ+0xb3/0x157
ret_from_intr+0x0/0x1d
cpuidle_enter_state+0x12f/0x1fd
cpuidle_enter+0x2e/0x3d
do_idle+0x1ce/0x2ce
cpu_startup_entry+0x1d/0x1f
start_kernel+0x406/0x46a
secondary_startup_64+0xa4/0xb0
other info that might help us debug this:
Chain exists of:
console_owner --> &port_lock_key --> &irq_desc_lock_class
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&irq_desc_lock_class);
lock(&port_lock_key);
lock(&irq_desc_lock_class);
lock(console_owner);
*** DEADLOCK ***
2 locks held by swapper/0/0:
#0: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba
hardkernel#1: ffffffffab65b5c0 (console_lock){+.+.}, at: console_trylock_spinning+0x20/0x181
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.39 hardkernel#55
Hardware name: XXXXXX
Call Trace:
<IRQ>
dump_stack+0xbf/0x133
? print_circular_bug+0xd6/0xe9
check_noncircular+0x1b9/0x1c3
__lock_acquire+0x118d/0x2714
lock_acquire+0x203/0x258
? console_lock_spinning_enable+0x31/0x57
console_lock_spinning_enable+0x51/0x57
? console_lock_spinning_enable+0x31/0x57
console_unlock+0x25d/0x528
? console_trylock+0x18/0x4e
vprintk_emit+0x111/0x17f
? lock_acquire+0x203/0x258
printk+0x59/0x73
__report_bad_irq+0xa3/0xba
note_interrupt+0x19a/0x1d6
handle_irq_event_percpu+0x57/0x79
handle_irq_event+0x36/0x55
handle_fasteoi_irq+0xc2/0x18a
do_IRQ+0xb3/0x157
common_interrupt+0xf/0xf
</IRQ>
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Fixes: 768aec0 ("serial: 8250: fix shared interrupts issues with SMP and RT kernels")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Raul Rangel <rrangel@google.com>
BugLink: https://bugs.chromium.org/p/chromium/issues/detail?id=1114800
Link: https://lore.kernel.org/lkml/CAHQZ30BnfX+gxjPm1DUd5psOTqbyDh4EJE=2=VAMW_VDafctkA@mail.gmail.com/T/#u
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200817022646.1484638-1-sergey.senozhatsky@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dangku pushed a commit to Dangku/amlogic-linux that referenced this pull request Apr 12, 2022
fixup! arm64: dts: overlay: VIM3L: Add ext_board dts
mdrjr pushed a commit that referenced this pull request Feb 8, 2024
[ Upstream commit dbc153f ]
A crash was found when dumping SMC-D connections. It can be reproduced
by following steps:
- run nginx/wrk test:
smc_run nginx
smc_run wrk -t 16 -c 1000 -d <duration> -H 'Connection: Close' <URL>
- continuously dump SMC-D connections in parallel:
watch -n 1 'smcss -D'
BUG: kernel NULL pointer dereference, address: 0000000000000030
CPU: 2 PID: 7204 Comm: smcss Kdump: loaded Tainted: G	E 6.7.0+ #55
RIP: 0010:__smc_diag_dump.constprop.0+0x5e5/0x620 [smc_diag]
Call Trace:
<TASK>
? __die+0x24/0x70
? page_fault_oops+0x66/0x150
? exc_page_fault+0x69/0x140
? asm_exc_page_fault+0x26/0x30
? __smc_diag_dump.constprop.0+0x5e5/0x620 [smc_diag]
? __kmalloc_node_track_caller+0x35d/0x430
? __alloc_skb+0x77/0x170
smc_diag_dump_proto+0xd0/0xf0 [smc_diag]
smc_diag_dump+0x26/0x60 [smc_diag]
netlink_dump+0x19f/0x320
__netlink_dump_start+0x1dc/0x300
smc_diag_handler_dump+0x6a/0x80 [smc_diag]
? __pfx_smc_diag_dump+0x10/0x10 [smc_diag]
sock_diag_rcv_msg+0x121/0x140
? __pfx_sock_diag_rcv_msg+0x10/0x10
netlink_rcv_skb+0x5a/0x110
sock_diag_rcv+0x28/0x40
netlink_unicast+0x22a/0x330
netlink_sendmsg+0x1f8/0x420
__sock_sendmsg+0xb0/0xc0
____sys_sendmsg+0x24e/0x300
? copy_msghdr_from_user+0x62/0x80
___sys_sendmsg+0x7c/0xd0
? __do_fault+0x34/0x160
? do_read_fault+0x5f/0x100
? do_fault+0xb0/0x110
? __handle_mm_fault+0x2b0/0x6c0
__sys_sendmsg+0x4d/0x80
do_syscall_64+0x69/0x180
entry_SYSCALL_64_after_hwframe+0x6e/0x76
It is possible that the connection is in process of being established
when we dump it. Assumed that the connection has been registered in a
link group by smc_conn_create() but the rmb_desc has not yet been
initialized by smc_buf_create(), thus causing the illegal access to
conn->rmb_desc. So fix it by checking before dump.
Fixes: 4b1b7d3 ("net/smc: add SMC-D diag support")
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
mdrjr pushed a commit that referenced this pull request Apr 15, 2024
[ Upstream commit dbc153f ]
A crash was found when dumping SMC-D connections. It can be reproduced
by following steps:
- run nginx/wrk test:
smc_run nginx
smc_run wrk -t 16 -c 1000 -d <duration> -H 'Connection: Close' <URL>
- continuously dump SMC-D connections in parallel:
watch -n 1 'smcss -D'
BUG: kernel NULL pointer dereference, address: 0000000000000030
CPU: 2 PID: 7204 Comm: smcss Kdump: loaded Tainted: G	E 6.7.0+ #55
RIP: 0010:__smc_diag_dump.constprop.0+0x5e5/0x620 [smc_diag]
Call Trace:
<TASK>
? __die+0x24/0x70
? page_fault_oops+0x66/0x150
? exc_page_fault+0x69/0x140
? asm_exc_page_fault+0x26/0x30
? __smc_diag_dump.constprop.0+0x5e5/0x620 [smc_diag]
? __kmalloc_node_track_caller+0x35d/0x430
? __alloc_skb+0x77/0x170
smc_diag_dump_proto+0xd0/0xf0 [smc_diag]
smc_diag_dump+0x26/0x60 [smc_diag]
netlink_dump+0x19f/0x320
__netlink_dump_start+0x1dc/0x300
smc_diag_handler_dump+0x6a/0x80 [smc_diag]
? __pfx_smc_diag_dump+0x10/0x10 [smc_diag]
sock_diag_rcv_msg+0x121/0x140
? __pfx_sock_diag_rcv_msg+0x10/0x10
netlink_rcv_skb+0x5a/0x110
sock_diag_rcv+0x28/0x40
netlink_unicast+0x22a/0x330
netlink_sendmsg+0x1f8/0x420
__sock_sendmsg+0xb0/0xc0
____sys_sendmsg+0x24e/0x300
? copy_msghdr_from_user+0x62/0x80
___sys_sendmsg+0x7c/0xd0
? __do_fault+0x34/0x160
? do_read_fault+0x5f/0x100
? do_fault+0xb0/0x110
? __handle_mm_fault+0x2b0/0x6c0
__sys_sendmsg+0x4d/0x80
do_syscall_64+0x69/0x180
entry_SYSCALL_64_after_hwframe+0x6e/0x76
It is possible that the connection is in process of being established
when we dump it. Assumed that the connection has been registered in a
link group by smc_conn_create() but the rmb_desc has not yet been
initialized by smc_buf_create(), thus causing the illegal access to
conn->rmb_desc. So fix it by checking before dump.
Fixes: 4b1b7d3 ("net/smc: add SMC-D diag support")
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
mdrjr pushed a commit that referenced this pull request Jan 29, 2025
…_bind returns err
[ Upstream commit 36684e9 ]
The pointer need to be set to NULL, otherwise KASAN complains about
use-after-free. Because in mtk_drm_bind, all private's drm are set
as follows.
private->all_drm_private[i]->drm = drm;
And drm will be released by drm_dev_put in case mtk_drm_kms_init returns
failure. However, the shutdown path still accesses the previous allocated
memory in drm_atomic_helper_shutdown.
[ 84.874820] watchdog: watchdog0: watchdog did not stop!
[ 86.512054] ==================================================================
[ 86.513162] BUG: KASAN: use-after-free in drm_atomic_helper_shutdown+0x33c/0x378
[ 86.514258] Read of size 8 at addr ffff0000d46fc068 by task shutdown/1
[ 86.515213]
[ 86.515455] CPU: 1 UID: 0 PID: 1 Comm: shutdown Not tainted 6.13.0-rc1-mtk+gfa1a78e5d24b-dirty #55
[ 86.516752] Hardware name: Unknown Product/Unknown Product, BIOS 2022.10 10/01/2022
[ 86.517960] Call trace:
[ 86.518333] show_stack+0x20/0x38 (C)
[ 86.518891] dump_stack_lvl+0x90/0xd0
[ 86.519443] print_report+0xf8/0x5b0
[ 86.519985] kasan_report+0xb4/0x100
[ 86.520526] __asan_report_load8_noabort+0x20/0x30
[ 86.521240] drm_atomic_helper_shutdown+0x33c/0x378
[ 86.521966] mtk_drm_shutdown+0x54/0x80
[ 86.522546] platform_shutdown+0x64/0x90
[ 86.523137] device_shutdown+0x260/0x5b8
[ 86.523728] kernel_restart+0x78/0xf0
[ 86.524282] __do_sys_reboot+0x258/0x2f0
[ 86.524871] __arm64_sys_reboot+0x90/0xd8
[ 86.525473] invoke_syscall+0x74/0x268
[ 86.526041] el0_svc_common.constprop.0+0xb0/0x240
[ 86.526751] do_el0_svc+0x4c/0x70
[ 86.527251] el0_svc+0x4c/0xc0
[ 86.527719] el0t_64_sync_handler+0x144/0x168
[ 86.528367] el0t_64_sync+0x198/0x1a0
[ 86.528920]
[ 86.529157] The buggy address belongs to the physical page:
[ 86.529972] page: refcount:0 mapcount:0 mapping:0000000000000000 index:0xffff0000d46fd4d0 pfn:0x1146fc
[ 86.531319] flags: 0xbfffc0000000000(node=0|zone=2|lastcpupid=0xffff)
[ 86.532267] raw: 0bfffc0000000000 0000000000000000 dead000000000122 0000000000000000
[ 86.533390] raw: ffff0000d46fd4d0 0000000000000000 00000000ffffffff 0000000000000000
[ 86.534511] page dumped because: kasan: bad access detected
[ 86.535323]
[ 86.535559] Memory state around the buggy address:
[ 86.536265] ffff0000d46fbf00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 86.537314] ffff0000d46fbf80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 86.538363] >ffff0000d46fc000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 86.544733] ^
[ 86.551057] ffff0000d46fc080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 86.557510] ffff0000d46fc100: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 86.563928] ==================================================================
[ 86.571093] Disabling lock debugging due to kernel taint
[ 86.577642] Unable to handle kernel paging request at virtual address e0e9c0920000000b
[ 86.581834] KASAN: maybe wild-memory-access in range [0x0752049000000058-0x075204900000005f]
...
Fixes: 1ef7ed4 ("drm/mediatek: Modify mediatek-drm for mt8195 multi mmsys support")
Signed-off-by: Guoqing Jiang <guoqing.jiang@canonical.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20241223023227.1258112-1-guoqing.jiang@canonical.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sign up for freeto join this conversation on GitHub. Already have an account? Sign in to comment

Labels

None yet

Projects

None yet

Development

Successfully merging this pull request may close these issues.

2 participants

@abradianu@mdrjr