6.18: Add Arduino VENTUNO Q (QCS8300) board support

Documentation/devicetree/bindings/arm/qcom.yaml

@@ -867,6 +867,7 @@ properties:
 
  - items:
  - enum:
+ - arduino,monza
  - qcom,monaco-ac-evk
  - qcom,monaco-evk
  - qcom,qcs8300-ride

Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml

@@ -28,7 +28,9 @@ properties:
  - ti,ina228
  - ti,ina230
  - ti,ina231
+ - ti,ina232
  - ti,ina233
+ - ti,ina234
  - ti,ina237
  - ti,ina238
  - ti,ina260
@@ -113,6 +115,8 @@ allOf:
  - ti,ina228
  - ti,ina230
  - ti,ina231
+ - ti,ina232
+ - ti,ina234
  - ti,ina237
  - ti,ina238
  - ti,ina260
@@ -134,6 +138,8 @@ allOf:
  - ti,ina226
  - ti,ina230
  - ti,ina231
+ - ti,ina232
+ - ti,ina234
  - ti,ina260
  - ti,ina700
  - ti,ina780

Documentation/devicetree/bindings/pinctrl/qcom,sm8450-lpass-lpi-pinctrl.yaml

@@ -15,7 +15,13 @@ description:
 
 properties:
  compatible:
- const: qcom,sm8450-lpass-lpi-pinctrl
+ oneOf:
+ - const: qcom,sm8450-lpass-lpi-pinctrl
+ - items:
+ - enum:
+ - qcom,qcs8300-lpass-lpi-pinctrl
+ - qcom,sa8775p-lpass-lpi-pinctrl
+ - const: qcom,sm8450-lpass-lpi-pinctrl
 
  reg:
  items:

Documentation/devicetree/bindings/sound/qcom,q6dsp-lpass-ports.yaml

@@ -126,13 +126,16 @@ patternProperties:
  reg:
  contains:
  # MI2S DAI ID range PRIMARY_MI2S_RX - QUATERNARY_MI2S_TX and
- # QUINARY_MI2S_RX - QUINARY_MI2S_TX
+ # QUINARY_MI2S_RX - QUINARY_MI2S_TX and
+ # LPI_MI2S_RX_0 - LPI_MI2S_TX_6
  items:
  oneOf:
  - minimum: 16
  maximum: 23
  - minimum: 127
  maximum: 128
+ - minimum: 137
+ maximum: 152
  then:
  required:
  - qcom,sd-lines

Documentation/devicetree/bindings/vendor-prefixes.yaml

@@ -154,6 +154,8 @@ patternProperties:
  description: Arctic Sand
  "^arcx,.*":
  description: arcx Inc. / Archronix Inc.
+ "^arduino,.*":
+ description: Arduino SRL
  "^argon40,.*":
  description: Argon 40 Technologies Limited
  "^ariaboard,.*":

Documentation/hwmon/ina2xx.rst

@@ -74,6 +74,16 @@ Supported chips:
  https://us1.silergy.com/
 
 
+ * Texas Instruments INA234
+
+ Prefix: 'ina234'
+
+ Addresses: I2C 0x40 - 0x43
+
+ Datasheet: Publicly available at the Texas Instruments website
+
+ https://www.ti.com/
+
 Author: Lothar Felten <lothar.felten@gmail.com>
 
 Description
@@ -89,7 +99,7 @@ interface. The INA220 monitors both shunt drop and supply voltage.
 The INA226 is a current shunt and power monitor with an I2C interface.
 The INA226 monitors both a shunt voltage drop and bus supply voltage.
 
-INA230and INA231 are high or low side current shunt and power monitors
+INA230, INA231, and INA234 are high or low side current shunt and power monitors
 with an I2C interface. The chips monitor both a shunt voltage drop and
 bus supply voltage.
 
@@ -124,8 +134,17 @@ power1_input Power(uW) measurement channel
 shunt_resistor Shunt resistance(uOhm) channel (not for ina260)
 ======================= ===============================================
 
-Additional sysfs entries for ina226, ina230, ina231, ina260, and sy24655
-------------------------------------------------------------------------
+Additional sysfs entries
+------------------------
+
+Additional entries are available for the following chips:
+
+ * ina226
+ * ina230
+ * ina231
+ * ina234
+ * ina260
+ * sy24655
 
 ======================= ====================================================
 curr1_lcrit Critical low current

arch/arm64/boot/dts/qcom/Makefile

@@ -58,6 +58,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= lemans-evk-el2.dtb
 lemans-evk-ifp-mezzanine-dtbs	:= lemans-evk.dtb lemans-evk-ifp-mezzanine.dtbo
 
 dtb-$(CONFIG_ARCH_QCOM)	+= lemans-evk-ifp-mezzanine.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= monaco-arduino-monza.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= monaco-ac-evk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= monaco-evk.dtb