new asix GBE driver 1.9.0 by megglos · Pull Request #32 · hardkernel/linux

megglos · 2014-01-14T22:02:48Z

see http://www.asix.com.tw/FrootAttach/driver/AX88179_178A_LINUX_DRIVER_v1.9.0_SOURCE.tar.bz2

…X88179_178A_LINUX_DRIVER_v1.9.0_SOURCE.tar.bz2

new asix GBE driver 1.9.0

Improve the comment of SW workaround for CCM lpm issue using hardware errata description to avoid confusion. ERR007265: CCM: When improper low-power sequence is used, the SoC enters low power mode before the ARM core executes WFI. Software workaround: 1) Software should trigger IRQ #32 (IOMUX) to be always pending by setting IOMUX_GPR1_GINT. 2) Software should then unmask IRQ #32 in GPC before setting CCM Low-Power mode. 3) Software should mask IRQ #32 right after CCM Low-Power mode is set (set bits 0-1 of CCM_CLPCR). Signed-off-by: Anson Huang <b20788@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

commit b1a06a4 upstream. Lockdep complains about btrfs's async commit: [ 2372.462171] [ BUG: bad unlock balance detected! ] [ 2372.462191] 3.12.0+ #32 Tainted: G W [ 2372.462209] ------------------------------------- [ 2372.462228] ceph-osd/14048 is trying to release lock (sb_internal) at: [ 2372.462275] [<ffffffffa022cb10>] btrfs_commit_transaction_async+0x1b0/0x2a0 [btrfs] [ 2372.462305] but there are no more locks to release! [ 2372.462324] [ 2372.462324] other info that might help us debug this: [ 2372.462349] no locks held by ceph-osd/14048. [ 2372.462367] [ 2372.462367] stack backtrace: [ 2372.462386] CPU: 2 PID: 14048 Comm: ceph-osd Tainted: G W 3.12.0+ #32 [ 2372.462414] Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./To be filled by O.E.M., BIOS 080015 11/09/2011 [ 2372.462455] ffffffffa022cb10 ffff88007490fd28 ffffffff816f094a ffff8800378aa320 [ 2372.462491] ffff88007490fd50 ffffffff810adf4c ffff8800378aa320 ffff88009af97650 [ 2372.462526] ffffffffa022cb10 ffff88007490fd88 ffffffff810b01ee ffff8800898c0000 [ 2372.462562] Call Trace: [ 2372.462584] [<ffffffffa022cb10>] ? btrfs_commit_transaction_async+0x1b0/0x2a0 [btrfs] [ 2372.462619] [<ffffffff816f094a>] dump_stack+0x45/0x56 [ 2372.462642] [<ffffffff810adf4c>] print_unlock_imbalance_bug+0xec/0x100 [ 2372.462677] [<ffffffffa022cb10>] ? btrfs_commit_transaction_async+0x1b0/0x2a0 [btrfs] [ 2372.462710] [<ffffffff810b01ee>] lock_release+0x18e/0x210 [ 2372.462742] [<ffffffffa022cb36>] btrfs_commit_transaction_async+0x1d6/0x2a0 [btrfs] [ 2372.462783] [<ffffffffa025a7ce>] btrfs_ioctl_start_sync+0x3e/0xc0 [btrfs] [ 2372.462822] [<ffffffffa025f1d3>] btrfs_ioctl+0x4c3/0x1f70 [btrfs] [ 2372.462849] [<ffffffff812c0321>] ? avc_has_perm+0x121/0x1b0 [ 2372.462873] [<ffffffff812c0224>] ? avc_has_perm+0x24/0x1b0 [ 2372.462897] [<ffffffff8107ecc8>] ? sched_clock_cpu+0xa8/0x100 [ 2372.462922] [<ffffffff8117b145>] do_vfs_ioctl+0x2e5/0x4e0 [ 2372.462946] [<ffffffff812c19e6>] ? file_has_perm+0x86/0xa0 [ 2372.462969] [<ffffffff8117b3c1>] SyS_ioctl+0x81/0xa0 [ 2372.462991] [<ffffffff817045a4>] tracesys+0xdd/0xe2 ==================================================== It's because that we don't do the right thing when checking if it's ok to tell lockdep that we're trying to release the rwsem. If the trans handle's type is TRANS_ATTACH, we won't acquire the freeze rwsem, but as TRANS_ATTACH fits the check (trans < TRANS_JOIN_NOLOCK), we'll release the freeze rwsem, which makes lockdep complains a lot. Reported-by: Ma Jianpeng <majianpeng@gmail.com> Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: Miao Xie <miaox@cn.fujitsu.com> Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

I can trigger a lockdep warning: # mount -t cgroup -o cpuset xxx /cgroup # mkdir /cgroup/cpuset # mkdir /cgroup/tmp # echo 0 > /cgroup/tmp/cpuset.cpus # echo 0 > /cgroup/tmp/cpuset.mems # echo 1 > /cgroup/tmp/cpuset.memory_migrate # echo $$ > /cgroup/tmp/tasks # echo 1 > /cgruop/tmp/cpuset.mems =============================== [ INFO: suspicious RCU usage. ] 3.14.0-rc1-0.1-default+ hardkernel#32 Not tainted ------------------------------- include/linux/cgroup.h:682 suspicious rcu_dereference_check() usage! ... [<ffffffff81582174>] dump_stack+0x72/0x86 [<ffffffff810b8f01>] lockdep_rcu_suspicious+0x101/0x140 [<ffffffff81105ba1>] cpuset_migrate_mm+0xb1/0xe0 ... We used to hold cgroup_mutex when calling cpuset_migrate_mm(), but now we hold cpuset_mutex, which causes task_css() to complain. This is not a false-positive but a real issue. Holding cpuset_mutex won't prevent a task from migrating to another cpuset, and it won't prevent the original task->cgroup from destroying during this change. Fixes: 5d21cc2 (cpuset: replace cgroup_mutex locking with cpuset internal locking) Cc: <stable@vger.kernel.org> # 3.9+ Signed-off-by: Li Zefan <lizefan@huawei.com> Sigend-off-by: Tejun Heo <tj@kernel.org>

When doing some numa tests on powerpc, I triggered an oops bug. I find it is caused by using page->_last_cpupid. It should be initialized as "-1 & LAST_CPUPID_MASK", but not "-1". Otherwise, in task_numa_fault(), we will miss the checking (last_cpupid == (-1 & LAST_CPUPID_MASK)). And finally cause an oops bug in task_numa_group(), since the online cpu is less than possible cpu. This happen with CONFIG_SPARSE_VMEMMAP disabled Call trace: SMP NR_CPUS=64 NUMA PowerNV Modules linked in: CPU: 24 PID: 804 Comm: systemd-udevd Not tainted3.13.0-rc1+ hardkernel#32 task: c000001e2746aa80 ti: c000001e32c50000 task.ti:c000001e32c50000 REGS: c000001e32c53510 TRAP: 0300 Not tainted(3.13.0-rc1+) MSR: 9000000000009032 <SF,HV,EE,ME,IR,DR,RI> CR:28024424 XER: 20000000 CFAR: c000000000009324 DAR: 7265717569726857 DSISR:40000000 SOFTE: 1 NIP .task_numa_fault+0x1470/0x2370 LR .task_numa_fault+0x1468/0x2370 Call Trace: .task_numa_fault+0x1468/0x2370 (unreliable) .do_numa_page+0x480/0x4a0 .handle_mm_fault+0x4ec/0xc90 .do_page_fault+0x3a8/0x890 handle_page_fault+0x10/0x30 Instruction dump: 3c82fefb 3884b138 48d9cff1 60000000 48000574 3c62fefb3863af78 3c82fefb 3884b138 48d9cfd5 60000000 e93f0100 <812902e4> 7d2907b45529063e 7d2a07b4 ---[ end trace 15f2510da5ae07cf ]--- Signed-off-by: Liu Ping Fan <pingfank@linux.vnet.ibm.com> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Mel Gorman <mel@csn.ul.ie> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

commit 4729583 upstream. I can trigger a lockdep warning: # mount -t cgroup -o cpuset xxx /cgroup # mkdir /cgroup/cpuset # mkdir /cgroup/tmp # echo 0 > /cgroup/tmp/cpuset.cpus # echo 0 > /cgroup/tmp/cpuset.mems # echo 1 > /cgroup/tmp/cpuset.memory_migrate # echo $$ > /cgroup/tmp/tasks # echo 1 > /cgruop/tmp/cpuset.mems =============================== [ INFO: suspicious RCU usage. ] 3.14.0-rc1-0.1-default+ #32 Not tainted ------------------------------- include/linux/cgroup.h:682 suspicious rcu_dereference_check() usage! ... [<ffffffff81582174>] dump_stack+0x72/0x86 [<ffffffff810b8f01>] lockdep_rcu_suspicious+0x101/0x140 [<ffffffff81105ba1>] cpuset_migrate_mm+0xb1/0xe0 ... We used to hold cgroup_mutex when calling cpuset_migrate_mm(), but now we hold cpuset_mutex, which causes task_css() to complain. This is not a false-positive but a real issue. Holding cpuset_mutex won't prevent a task from migrating to another cpuset, and it won't prevent the original task->cgroup from destroying during this change. Fixes: 5d21cc2 (cpuset: replace cgroup_mutex locking with cpuset internal locking) Signed-off-by: Li Zefan <lizefan@huawei.com> Sigend-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4729583 upstream. I can trigger a lockdep warning: # mount -t cgroup -o cpuset xxx /cgroup # mkdir /cgroup/cpuset # mkdir /cgroup/tmp # echo 0 > /cgroup/tmp/cpuset.cpus # echo 0 > /cgroup/tmp/cpuset.mems # echo 1 > /cgroup/tmp/cpuset.memory_migrate # echo $$ > /cgroup/tmp/tasks # echo 1 > /cgruop/tmp/cpuset.mems =============================== [ INFO: suspicious RCU usage. ] 3.14.0-rc1-0.1-default+ #32 Not tainted ------------------------------- include/linux/cgroup.h:682 suspicious rcu_dereference_check() usage! ... [<ffffffff81582174>] dump_stack+0x72/0x86 [<ffffffff810b8f01>] lockdep_rcu_suspicious+0x101/0x140 [<ffffffff81105ba1>] cpuset_migrate_mm+0xb1/0xe0 ... We used to hold cgroup_mutex when calling cpuset_migrate_mm(), but now we hold cpuset_mutex, which causes task_css() to complain. This is not a false-positive but a real issue. Holding cpuset_mutex won't prevent a task from migrating to another cpuset, and it won't prevent the original task->cgroup from destroying during this change. Fixes: 5d21cc2 (cpuset: replace cgroup_mutex locking with cpuset internal locking) Signed-off-by: Li Zefan <lizefan@huawei.com> Sigend-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>

Nikolay has reported a hang when a memcg reclaim got stuck with the following backtrace: PID: 18308 TASK: ffff883d7c9b0a30 CPU: 1 COMMAND: "rsync" #0 __schedule at ffffffff815ab152 hardkernel#1 schedule at ffffffff815ab76e hardkernel#2 schedule_timeout at ffffffff815ae5e5 hardkernel#3 io_schedule_timeout at ffffffff815aad6a hardkernel#4 bit_wait_io at ffffffff815abfc6 hardkernel#5 __wait_on_bit at ffffffff815abda5 hardkernel#6 wait_on_page_bit at ffffffff8111fd4f hardkernel#7 shrink_page_list at ffffffff81135445 hardkernel#8 shrink_inactive_list at ffffffff81135845 hardkernel#9 shrink_lruvec at ffffffff81135ead hardkernel#10 shrink_zone at ffffffff811360c3 hardkernel#11 shrink_zones at ffffffff81136eff hardkernel#12 do_try_to_free_pages at ffffffff8113712f hardkernel#13 try_to_free_mem_cgroup_pages at ffffffff811372be hardkernel#14 try_charge at ffffffff81189423 hardkernel#15 mem_cgroup_try_charge at ffffffff8118c6f5 hardkernel#16 __add_to_page_cache_locked at ffffffff8112137d hardkernel#17 add_to_page_cache_lru at ffffffff81121618 hardkernel#18 pagecache_get_page at ffffffff8112170b hardkernel#19 grow_dev_page at ffffffff811c8297 hardkernel#20 __getblk_slow at ffffffff811c91d6 hardkernel#21 __getblk_gfp at ffffffff811c92c1 hardkernel#22 ext4_ext_grow_indepth at ffffffff8124565c hardkernel#23 ext4_ext_create_new_leaf at ffffffff81246ca8 hardkernel#24 ext4_ext_insert_extent at ffffffff81246f09 hardkernel#25 ext4_ext_map_blocks at ffffffff8124a848 hardkernel#26 ext4_map_blocks at ffffffff8121a5b7 hardkernel#27 mpage_map_one_extent at ffffffff8121b1fa hardkernel#28 mpage_map_and_submit_extent at ffffffff8121f07b hardkernel#29 ext4_writepages at ffffffff8121f6d5 hardkernel#30 do_writepages at ffffffff8112c490 hardkernel#31 __filemap_fdatawrite_range at ffffffff81120199 hardkernel#32 filemap_flush at ffffffff8112041c hardkernel#33 ext4_alloc_da_blocks at ffffffff81219da1 hardkernel#34 ext4_rename at ffffffff81229b91 hardkernel#35 ext4_rename2 at ffffffff81229e32 hardkernel#36 vfs_rename at ffffffff811a08a5 hardkernel#37 SYSC_renameat2 at ffffffff811a3ffc hardkernel#38 sys_renameat2 at ffffffff811a408e hardkernel#39 sys_rename at ffffffff8119e51e hardkernel#40 system_call_fastpath at ffffffff815afa89 Dave Chinner has properly pointed out that this is a deadlock in the reclaim code because ext4 doesn't submit pages which are marked by PG_writeback right away. The heuristic was introduced by commit e62e384 ("memcg: prevent OOM with too many dirty pages") and it was applied only when may_enter_fs was specified. The code has been changed by c3b94f4 ("memcg: further prevent OOM with too many dirty pages") which has removed the __GFP_FS restriction with a reasoning that we do not get into the fs code. But this is not sufficient apparently because the fs doesn't necessarily submit pages marked PG_writeback for IO right away. ext4_bio_write_page calls io_submit_add_bh but that doesn't necessarily submit the bio. Instead it tries to map more pages into the bio and mpage_map_one_extent might trigger memcg charge which might end up waiting on a page which is marked PG_writeback but hasn't been submitted yet so we would end up waiting for something that never finishes. Fix this issue by replacing __GFP_IO by may_enter_fs check (for case 2) before we go to wait on the writeback. The page fault path, which is the only path that triggers memcg oom killer since 3.12, shouldn't require GFP_NOFS and so we shouldn't reintroduce the premature OOM killer issue which was originally addressed by the heuristic. As per David Chinner the xfs is doing similar thing since 2.6.15 already so ext4 is not the only affected filesystem. Moreover he notes: : For example: IO completion might require unwritten extent conversion : which executes filesystem transactions and GFP_NOFS allocations. The : writeback flag on the pages can not be cleared until unwritten : extent conversion completes. Hence memory reclaim cannot wait on : page writeback to complete in GFP_NOFS context because it is not : safe to do so, memcg reclaim or otherwise. Cc: stable@vger.kernel.org # 3.9+ [tytso@mit.edu: corrected the control flow] Fixes: c3b94f4 ("memcg: further prevent OOM with too many dirty pages") Reported-by: Nikolay Borisov <kernel@kyup.com> Signed-off-by: Michal Hocko <mhocko@suse.cz> Signed-off-by: Hugh Dickins <hughd@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

commit bcdbeb8 upstream. The stop_activity() routine in dummy-hcd is supposed to unlink all active requests for every endpoint, among other things. But it doesn't handle ep0. As a result, fuzz testing can generate a WARNING like the following: WARNING: CPU: 0 PID: 4410 at drivers/usb/gadget/udc/dummy_hcd.c:672 dummy_free_request+0x153/0x170 Modules linked in: CPU: 0 PID: 4410 Comm: syz-executor Not tainted 4.9.0-rc7+ hardkernel#32 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 ffff88006a64ed10 ffffffff81f96b8a ffffffff41b58ab3 1ffff1000d4c9d35 ffffed000d4c9d2d ffff880065f8ac00 0000000041b58ab3 ffffffff8598b510 ffffffff81f968f8 0000000041b58ab3 ffffffff859410e0 ffffffff813f0590 Call Trace: [< inline >] __dump_stack lib/dump_stack.c:15 [<ffffffff81f96b8a>] dump_stack+0x292/0x398 lib/dump_stack.c:51 [<ffffffff812b808f>] __warn+0x19f/0x1e0 kernel/panic.c:550 [<ffffffff812b831c>] warn_slowpath_null+0x2c/0x40 kernel/panic.c:585 [<ffffffff830fcb13>] dummy_free_request+0x153/0x170 drivers/usb/gadget/udc/dummy_hcd.c:672 [<ffffffff830ed1b0>] usb_ep_free_request+0xc0/0x420 drivers/usb/gadget/udc/core.c:195 [<ffffffff83225031>] gadgetfs_unbind+0x131/0x190 drivers/usb/gadget/legacy/inode.c:1612 [<ffffffff830ebd8f>] usb_gadget_remove_driver+0x10f/0x2b0 drivers/usb/gadget/udc/core.c:1228 [<ffffffff830ec084>] usb_gadget_unregister_driver+0x154/0x240 drivers/usb/gadget/udc/core.c:1357 This patch fixes the problem by iterating over all the endpoints in the driver's ep array instead of iterating over the gadget's ep_list, which explicitly leaves out ep0. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit ddc665a ] When the instruction right before the branch destination is a 64 bit load immediate, we currently calculate the wrong jump offset in the ctx->offset[] array as we only account one instruction slot for the 64 bit load immediate although it uses two BPF instructions. Fix it up by setting the offset into the right slot after we incremented the index. Before (ldimm64 test 1): [...] 00000020: 52800007 mov w7, #0x0 // #0 00000024: d2800060 mov x0, #0x3 // hardkernel#3 00000028: d2800041 mov x1, #0x2 // hardkernel#2 0000002c: eb01001f cmp x0, x1 00000030: 54ffff82 b.cs 0x00000020 00000034: d29fffe7 mov x7, #0xffff // #65535 00000038: f2bfffe7 movk x7, #0xffff, lsl hardkernel#16 0000003c: f2dfffe7 movk x7, #0xffff, lsl hardkernel#32 00000040: f2ffffe7 movk x7, #0xffff, lsl hardkernel#48 00000044: d29dddc7 mov x7, #0xeeee // #61166 00000048: f2bdddc7 movk x7, #0xeeee, lsl hardkernel#16 0000004c: f2ddddc7 movk x7, #0xeeee, lsl hardkernel#32 00000050: f2fdddc7 movk x7, #0xeeee, lsl hardkernel#48 [...] After (ldimm64 test 1): [...] 00000020: 52800007 mov w7, #0x0 // #0 00000024: d2800060 mov x0, #0x3 // hardkernel#3 00000028: d2800041 mov x1, #0x2 // hardkernel#2 0000002c: eb01001f cmp x0, x1 00000030: 540000a2 b.cs 0x00000044 00000034: d29fffe7 mov x7, #0xffff // #65535 00000038: f2bfffe7 movk x7, #0xffff, lsl hardkernel#16 0000003c: f2dfffe7 movk x7, #0xffff, lsl hardkernel#32 00000040: f2ffffe7 movk x7, #0xffff, lsl hardkernel#48 00000044: d29dddc7 mov x7, #0xeeee // #61166 00000048: f2bdddc7 movk x7, #0xeeee, lsl hardkernel#16 0000004c: f2ddddc7 movk x7, #0xeeee, lsl hardkernel#32 00000050: f2fdddc7 movk x7, #0xeeee, lsl hardkernel#48 [...] Also, add a couple of test cases to make sure JITs pass this test. Tested on Cavium ThunderX ARMv8. The added test cases all pass after the fix. Fixes: 8eee539 ("arm64: bpf: fix out-of-bounds read in bpf2a64_offset()") Reported-by: David S. Miller <davem@davemloft.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Cc: Xi Wang <xi.wang@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 79514ef ] Commit a47b70e ("ravb: unmap descriptors when freeing rings") has introduced the issue seen in [1] reproduced on H3ULCB board. Fix this by relocating the RX skb ringbuffer free operation, so that swiotlb page unmapping can be done first. Freeing of aligned TX buffers is not relevant to the issue seen in [1]. Still, reposition TX free calls as well, to have all kfree() operations performed consistently _after_ dma_unmap_*()/dma_free_*(). [1] Console screenshot with the problem reproduced: salvator-x login: root root@salvator-x:~# ifconfig eth0 up Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: \ attached PHY driver [Micrel KSZ9031 Gigabit PHY] \ (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=235) IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready root@salvator-x:~# root@salvator-x:~# ifconfig eth0 down ================================================================== BUG: KASAN: use-after-free in swiotlb_tbl_unmap_single+0xc4/0x35c Write of size 1538 at addr ffff8006d884f780 by task ifconfig/1649 CPU: 0 PID: 1649 Comm: ifconfig Not tainted 4.12.0-rc4-00004-g112eb07287d1 hardkernel#32 Hardware name: Renesas H3ULCB board based on r8a7795 (DT) Call trace: [<ffff20000808f11c>] dump_backtrace+0x0/0x3a4 [<ffff20000808f4d4>] show_stack+0x14/0x1c [<ffff20000865970c>] dump_stack+0xf8/0x150 [<ffff20000831f8b0>] print_address_description+0x7c/0x330 [<ffff200008320010>] kasan_report+0x2e0/0x2f4 [<ffff20000831eac0>] check_memory_region+0x20/0x14c [<ffff20000831f054>] memcpy+0x48/0x68 [<ffff20000869ed50>] swiotlb_tbl_unmap_single+0xc4/0x35c [<ffff20000869fcf4>] unmap_single+0x90/0xa4 [<ffff20000869fd14>] swiotlb_unmap_page+0xc/0x14 [<ffff2000080a2974>] __swiotlb_unmap_page+0xcc/0xe4 [<ffff2000088acdb8>] ravb_ring_free+0x514/0x870 [<ffff2000088b25dc>] ravb_close+0x288/0x36c [<ffff200008aaf8c4>] __dev_close_many+0x14c/0x174 [<ffff200008aaf9b4>] __dev_close+0xc8/0x144 [<ffff200008ac2100>] __dev_change_flags+0xd8/0x194 [<ffff200008ac221c>] dev_change_flags+0x60/0xb0 [<ffff200008ba2dec>] devinet_ioctl+0x484/0x9d4 [<ffff200008ba7b78>] inet_ioctl+0x190/0x194 [<ffff200008a78c44>] sock_do_ioctl+0x78/0xa8 [<ffff200008a7a128>] sock_ioctl+0x110/0x3c4 [<ffff200008365a70>] vfs_ioctl+0x90/0xa0 [<ffff200008365dbc>] do_vfs_ioctl+0x148/0xc38 [<ffff2000083668f0>] SyS_ioctl+0x44/0x74 [<ffff200008083770>] el0_svc_naked+0x24/0x28 The buggy address belongs to the page: page:ffff7e001b6213c0 count:0 mapcount:0 mapping: (null) index:0x0 flags: 0x4000000000000000() raw: 4000000000000000 0000000000000000 0000000000000000 00000000ffffffff raw: 0000000000000000 ffff7e001b6213e0 0000000000000000 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8006d884f680: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff8006d884f700: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >ffff8006d884f780: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ^ ffff8006d884f800: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff8006d884f880: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ================================================================== Disabling lock debugging due to kernel taint root@salvator-x:~# Fixes: a47b70e ("ravb: unmap descriptors when freeing rings") Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 5bfd37b ] syszkaller reported use-after-free in tipc [1] When msg->rep skb is freed, set the pointer to NULL, so that caller does not free it again. [1] ================================================================== BUG: KASAN: use-after-free in skb_push+0xd4/0xe0 net/core/skbuff.c:1466 Read of size 8 at addr ffff8801c6e71e90 by task syz-executor5/4115 CPU: 1 PID: 4115 Comm: syz-executor5 Not tainted 4.13.0-rc4+ hardkernel#32 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:16 [inline] dump_stack+0x194/0x257 lib/dump_stack.c:52 print_address_description+0x73/0x250 mm/kasan/report.c:252 kasan_report_error mm/kasan/report.c:351 [inline] kasan_report+0x24e/0x340 mm/kasan/report.c:409 __asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:430 skb_push+0xd4/0xe0 net/core/skbuff.c:1466 tipc_nl_compat_recv+0x833/0x18f0 net/tipc/netlink_compat.c:1209 genl_family_rcv_msg+0x7b7/0xfb0 net/netlink/genetlink.c:598 genl_rcv_msg+0xb2/0x140 net/netlink/genetlink.c:623 netlink_rcv_skb+0x216/0x440 net/netlink/af_netlink.c:2397 genl_rcv+0x28/0x40 net/netlink/genetlink.c:634 netlink_unicast_kernel net/netlink/af_netlink.c:1265 [inline] netlink_unicast+0x4e8/0x6f0 net/netlink/af_netlink.c:1291 netlink_sendmsg+0xa4a/0xe60 net/netlink/af_netlink.c:1854 sock_sendmsg_nosec net/socket.c:633 [inline] sock_sendmsg+0xca/0x110 net/socket.c:643 sock_write_iter+0x31a/0x5d0 net/socket.c:898 call_write_iter include/linux/fs.h:1743 [inline] new_sync_write fs/read_write.c:457 [inline] __vfs_write+0x684/0x970 fs/read_write.c:470 vfs_write+0x189/0x510 fs/read_write.c:518 SYSC_write fs/read_write.c:565 [inline] SyS_write+0xef/0x220 fs/read_write.c:557 entry_SYSCALL_64_fastpath+0x1f/0xbe RIP: 0033:0x4512e9 RSP: 002b:00007f3bc8184c08 EFLAGS: 00000216 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 0000000000718000 RCX: 00000000004512e9 RDX: 0000000000000020 RSI: 0000000020fdb000 RDI: 0000000000000006 RBP: 0000000000000086 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000216 R12: 00000000004b5e76 R13: 00007f3bc8184b48 R14: 00000000004b5e86 R15: 0000000000000000 Allocated by task 4115: save_stack_trace+0x16/0x20 arch/x86/kernel/stacktrace.c:59 save_stack+0x43/0xd0 mm/kasan/kasan.c:447 set_track mm/kasan/kasan.c:459 [inline] kasan_kmalloc+0xad/0xe0 mm/kasan/kasan.c:551 kasan_slab_alloc+0x12/0x20 mm/kasan/kasan.c:489 kmem_cache_alloc_node+0x13d/0x750 mm/slab.c:3651 __alloc_skb+0xf1/0x740 net/core/skbuff.c:219 alloc_skb include/linux/skbuff.h:903 [inline] tipc_tlv_alloc+0x26/0xb0 net/tipc/netlink_compat.c:148 tipc_nl_compat_dumpit+0xf2/0x3c0 net/tipc/netlink_compat.c:248 tipc_nl_compat_handle net/tipc/netlink_compat.c:1130 [inline] tipc_nl_compat_recv+0x756/0x18f0 net/tipc/netlink_compat.c:1199 genl_family_rcv_msg+0x7b7/0xfb0 net/netlink/genetlink.c:598 genl_rcv_msg+0xb2/0x140 net/netlink/genetlink.c:623 netlink_rcv_skb+0x216/0x440 net/netlink/af_netlink.c:2397 genl_rcv+0x28/0x40 net/netlink/genetlink.c:634 netlink_unicast_kernel net/netlink/af_netlink.c:1265 [inline] netlink_unicast+0x4e8/0x6f0 net/netlink/af_netlink.c:1291 netlink_sendmsg+0xa4a/0xe60 net/netlink/af_netlink.c:1854 sock_sendmsg_nosec net/socket.c:633 [inline] sock_sendmsg+0xca/0x110 net/socket.c:643 sock_write_iter+0x31a/0x5d0 net/socket.c:898 call_write_iter include/linux/fs.h:1743 [inline] new_sync_write fs/read_write.c:457 [inline] __vfs_write+0x684/0x970 fs/read_write.c:470 vfs_write+0x189/0x510 fs/read_write.c:518 SYSC_write fs/read_write.c:565 [inline] SyS_write+0xef/0x220 fs/read_write.c:557 entry_SYSCALL_64_fastpath+0x1f/0xbe Freed by task 4115: save_stack_trace+0x16/0x20 arch/x86/kernel/stacktrace.c:59 save_stack+0x43/0xd0 mm/kasan/kasan.c:447 set_track mm/kasan/kasan.c:459 [inline] kasan_slab_free+0x71/0xc0 mm/kasan/kasan.c:524 __cache_free mm/slab.c:3503 [inline] kmem_cache_free+0x77/0x280 mm/slab.c:3763 kfree_skbmem+0x1a1/0x1d0 net/core/skbuff.c:622 __kfree_skb net/core/skbuff.c:682 [inline] kfree_skb+0x165/0x4c0 net/core/skbuff.c:699 tipc_nl_compat_dumpit+0x36a/0x3c0 net/tipc/netlink_compat.c:260 tipc_nl_compat_handle net/tipc/netlink_compat.c:1130 [inline] tipc_nl_compat_recv+0x756/0x18f0 net/tipc/netlink_compat.c:1199 genl_family_rcv_msg+0x7b7/0xfb0 net/netlink/genetlink.c:598 genl_rcv_msg+0xb2/0x140 net/netlink/genetlink.c:623 netlink_rcv_skb+0x216/0x440 net/netlink/af_netlink.c:2397 genl_rcv+0x28/0x40 net/netlink/genetlink.c:634 netlink_unicast_kernel net/netlink/af_netlink.c:1265 [inline] netlink_unicast+0x4e8/0x6f0 net/netlink/af_netlink.c:1291 netlink_sendmsg+0xa4a/0xe60 net/netlink/af_netlink.c:1854 sock_sendmsg_nosec net/socket.c:633 [inline] sock_sendmsg+0xca/0x110 net/socket.c:643 sock_write_iter+0x31a/0x5d0 net/socket.c:898 call_write_iter include/linux/fs.h:1743 [inline] new_sync_write fs/read_write.c:457 [inline] __vfs_write+0x684/0x970 fs/read_write.c:470 vfs_write+0x189/0x510 fs/read_write.c:518 SYSC_write fs/read_write.c:565 [inline] SyS_write+0xef/0x220 fs/read_write.c:557 entry_SYSCALL_64_fastpath+0x1f/0xbe The buggy address belongs to the object at ffff8801c6e71dc0 which belongs to the cache skbuff_head_cache of size 224 The buggy address is located 208 bytes inside of 224-byte region [ffff8801c6e71dc0, ffff8801c6e71ea0) The buggy address belongs to the page: page:ffffea00071b9c40 count:1 mapcount:0 mapping:ffff8801c6e71000 index:0x0 flags: 0x200000000000100(slab) raw: 0200000000000100 ffff8801c6e71000 0000000000000000 000000010000000c raw: ffffea0007224a20 ffff8801d98caf48 ffff8801d9e79040 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8801c6e71d80: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb ffff8801c6e71e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb >ffff8801c6e71e80: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff8801c6e71f00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8801c6e71f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ================================================================== Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Jon Maloy <jon.maloy@ericsson.com> Cc: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit bcdbeb8 upstream. The stop_activity() routine in dummy-hcd is supposed to unlink all active requests for every endpoint, among other things. But it doesn't handle ep0. As a result, fuzz testing can generate a WARNING like the following: WARNING: CPU: 0 PID: 4410 at drivers/usb/gadget/udc/dummy_hcd.c:672 dummy_free_request+0x153/0x170 Modules linked in: CPU: 0 PID: 4410 Comm: syz-executor Not tainted 4.9.0-rc7+ #32 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 ffff88006a64ed10 ffffffff81f96b8a ffffffff41b58ab3 1ffff1000d4c9d35 ffffed000d4c9d2d ffff880065f8ac00 0000000041b58ab3 ffffffff8598b510 ffffffff81f968f8 0000000041b58ab3 ffffffff859410e0 ffffffff813f0590 Call Trace: [< inline >] __dump_stack lib/dump_stack.c:15 [<ffffffff81f96b8a>] dump_stack+0x292/0x398 lib/dump_stack.c:51 [<ffffffff812b808f>] __warn+0x19f/0x1e0 kernel/panic.c:550 [<ffffffff812b831c>] warn_slowpath_null+0x2c/0x40 kernel/panic.c:585 [<ffffffff830fcb13>] dummy_free_request+0x153/0x170 drivers/usb/gadget/udc/dummy_hcd.c:672 [<ffffffff830ed1b0>] usb_ep_free_request+0xc0/0x420 drivers/usb/gadget/udc/core.c:195 [<ffffffff83225031>] gadgetfs_unbind+0x131/0x190 drivers/usb/gadget/legacy/inode.c:1612 [<ffffffff830ebd8f>] usb_gadget_remove_driver+0x10f/0x2b0 drivers/usb/gadget/udc/core.c:1228 [<ffffffff830ec084>] usb_gadget_unregister_driver+0x154/0x240 drivers/usb/gadget/udc/core.c:1357 This patch fixes the problem by iterating over all the endpoints in the driver's ep array instead of iterating over the gadget's ep_list, which explicitly leaves out ep0. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Willy Tarreau <w@1wt.eu>

…rse nlmsg properly commit c88f0e6 upstream. ChunYu found a kernel crash by syzkaller: [ 651.617875] kasan: CONFIG_KASAN_INLINE enabled [ 651.618217] kasan: GPF could be caused by NULL-ptr deref or user memory access [ 651.618731] general protection fault: 0000 [hardkernel#1] SMP KASAN [ 651.621543] CPU: 1 PID: 9539 Comm: scsi Not tainted 4.11.0.cov hardkernel#32 [ 651.621938] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 [ 651.622309] task: ffff880117780000 task.stack: ffff8800a3188000 [ 651.622762] RIP: 0010:skb_release_data+0x26c/0x590 [...] [ 651.627260] Call Trace: [ 651.629156] skb_release_all+0x4f/0x60 [ 651.629450] consume_skb+0x1a5/0x600 [ 651.630705] netlink_unicast+0x505/0x720 [ 651.632345] netlink_sendmsg+0xab2/0xe70 [ 651.633704] sock_sendmsg+0xcf/0x110 [ 651.633942] ___sys_sendmsg+0x833/0x980 [ 651.637117] __sys_sendmsg+0xf3/0x240 [ 651.638820] SyS_sendmsg+0x32/0x50 [ 651.639048] entry_SYSCALL_64_fastpath+0x1f/0xc2 It's caused by skb_shared_info at the end of sk_buff was overwritten by ISCSI_KEVENT_IF_ERROR when parsing nlmsg info from skb in iscsi_if_rx. During the loop if skb->len == nlh->nlmsg_len and both are sizeof(*nlh), ev = nlmsg_data(nlh) will acutally get skb_shinfo(SKB) instead and set a new value to skb_shinfo(SKB)->nr_frags by ev->type. This patch is to fix it by checking nlh->nlmsg_len properly there to avoid over accessing sk_buff. Reported-by: ChunYu Wang <chunwang@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Chris Leech <cleech@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f4483f2 upstream. When a tail call fails, it is documented that the tail call should continue execution at the following instruction. An example tail call sequence is: 12: (85) call bpf_tail_call#12 13: (b7) r0 = 0 14: (95) exit The ARM assembler for the tail call in this case ends up branching to instruction 14 instead of instruction 13, resulting in the BPF filter returning a non-zero value: 178: ldr r8, [sp, #588] ; insn 12 17c: ldr r6, [r8, r6] 180: ldr r8, [sp, #580] 184: cmp r8, r6 188: bcs 0x1e8 18c: ldr r6, [sp, #524] 190: ldr r7, [sp, #528] 194: cmp r7, #0 198: cmpeq r6, #32 19c: bhi 0x1e8 1a0: adds r6, r6, #1 1a4: adc r7, r7, #0 1a8: str r6, [sp, #524] 1ac: str r7, [sp, #528] 1b0: mov r6, #104 1b4: ldr r8, [sp, #588] 1b8: add r6, r8, r6 1bc: ldr r8, [sp, #580] 1c0: lsl r7, r8, #2 1c4: ldr r6, [r6, r7] 1c8: cmp r6, #0 1cc: beq 0x1e8 1d0: mov r8, #32 1d4: ldr r6, [r6, r8] 1d8: add r6, r6, #44 1dc: bx r6 1e0: mov r0, #0 ; insn 13 1e4: mov r1, #0 1e8: add sp, sp, #596 ; insn 14 1ec: pop {r4, r5, r6, r7, r8, sl, pc} For other sequences, the tail call could end up branching midway through the following BPF instructions, or maybe off the end of the function, leading to unknown behaviours. Fixes: 39c13c2 ("arm: eBPF JIT compiler") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f298103 upstream. Reported by syzkaller: WARNING: CPU: 0 PID: 27962 at arch/x86/kvm/emulate.c:5631 x86_emulate_insn+0x557/0x15f0 [kvm] Modules linked in: kvm_intel kvm [last unloaded: kvm] CPU: 0 PID: 27962 Comm: syz-executor Tainted: G B W 4.15.0-rc2-next-20171208+ #32 Hardware name: Intel Corporation S1200SP/S1200SP, BIOS S1200SP.86B.01.03.0006.040720161253 04/07/2016 RIP: 0010:x86_emulate_insn+0x557/0x15f0 [kvm] RSP: 0018:ffff8807234476d0 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffff88072d0237a0 RCX: ffffffffa0065c4d RDX: 1ffff100e5a046f9 RSI: 0000000000000003 RDI: ffff88072d0237c8 RBP: ffff880723447728 R08: ffff88072d020000 R09: ffffffffa008d240 R10: 0000000000000002 R11: ffffed00e7d87db3 R12: ffff88072d0237c8 R13: ffff88072d023870 R14: ffff88072d0238c2 R15: ffffffffa008d080 FS: 00007f8a68666700(0000) GS:ffff880802200000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000002009506c CR3: 000000071fec4005 CR4: 00000000003626f0 Call Trace: x86_emulate_instruction+0x3bc/0xb70 [kvm] ? reexecute_instruction.part.162+0x130/0x130 [kvm] vmx_handle_exit+0x46d/0x14f0 [kvm_intel] ? trace_event_raw_event_kvm_entry+0xe7/0x150 [kvm] ? handle_vmfunc+0x2f0/0x2f0 [kvm_intel] ? wait_lapic_expire+0x25/0x270 [kvm] vcpu_enter_guest+0x720/0x1ef0 [kvm] ... When CS.L is set, vcpu should run in the 64 bit paging mode. Current kvm set_sregs function doesn't have such check when userspace inputs sreg values. This will lead unexpected behavior. This patch is to add checks for CS.L, EFER.LME, EFER.LMA and CR4.PAE when get SREG inputs from userspace in order to avoid unexpected behavior. Suggested-by: Paolo Bonzini <pbonzini@redhat.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Jim Mattson <jmattson@google.com> Signed-off-by: Tianyu Lan <tianyu.lan@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ upstream commit 16338a9 ] I recently noticed a crash on arm64 when feeding a bogus index into BPF tail call helper. The crash would not occur when the interpreter is used, but only in case of JIT. Output looks as follows: [ 347.007486] Unable to handle kernel paging request at virtual address fffb850e96492510 [...] [ 347.043065] [fffb850e96492510] address between user and kernel address ranges [ 347.050205] Internal error: Oops: 96000004 [#1] SMP [...] [ 347.190829] x13: 0000000000000000 x12: 0000000000000000 [ 347.196128] x11: fffc047ebe782800 x10: ffff808fd7d0fd10 [ 347.201427] x9 : 0000000000000000 x8 : 0000000000000000 [ 347.206726] x7 : 0000000000000000 x6 : 001c991738000000 [ 347.212025] x5 : 0000000000000018 x4 : 000000000000ba5a [ 347.217325] x3 : 00000000000329c4 x2 : ffff808fd7cf0500 [ 347.222625] x1 : ffff808fd7d0fc00 x0 : ffff808fd7cf0500 [ 347.227926] Process test_verifier (pid: 4548, stack limit = 0x000000007467fa61) [ 347.235221] Call trace: [ 347.237656] 0xffff000002f3a4fc [ 347.240784] bpf_test_run+0x78/0xf8 [ 347.244260] bpf_prog_test_run_skb+0x148/0x230 [ 347.248694] SyS_bpf+0x77c/0x1110 [ 347.251999] el0_svc_naked+0x30/0x34 [ 347.255564] Code: 9100075a d280220a 8b0a002a d37df04b (f86b694b) [...] In this case the index used in BPF r3 is the same as in r1 at the time of the call, meaning we fed a pointer as index; here, it had the value 0xffff808fd7cf0500 which sits in x2. While I found tail calls to be working in general (also for hitting the error cases), I noticed the following in the code emission: # bpftool p d j i 988 [...] 38: ldr w10, [x1,x10] 3c: cmp w2, w10 40: b.ge 0x000000000000007c <-- signed cmp 44: mov x10, #0x20 // #32 48: cmp x26, x10 4c: b.gt 0x000000000000007c 50: add x26, x26, #0x1 54: mov x10, #0x110 // #272 58: add x10, x1, x10 5c: lsl x11, x2, #3 60: ldr x11, [x10,x11] <-- faulting insn (f86b694b) 64: cbz x11, 0x000000000000007c [...] Meaning, the tests passed because commit ddb5599 ("arm64: bpf: implement bpf_tail_call() helper") was using signed compares instead of unsigned which as a result had the test wrongly passing. Change this but also the tail call count test both into unsigned and cap the index as u32. Latter we did as well in 90caccd ("bpf: fix bpf_tail_call() x64 JIT") and is needed in addition here, too. Tested on HiSilicon Hi1616. Result after patch: # bpftool p d j i 268 [...] 38: ldr w10, [x1,x10] 3c: add w2, w2, #0x0 40: cmp w2, w10 44: b.cs 0x0000000000000080 48: mov x10, #0x20 // #32 4c: cmp x26, x10 50: b.hi 0x0000000000000080 54: add x26, x26, #0x1 58: mov x10, #0x110 // #272 5c: add x10, x1, x10 60: lsl x11, x2, #3 64: ldr x11, [x10,x11] 68: cbz x11, 0x0000000000000080 [...] Fixes: ddb5599 ("arm64: bpf: implement bpf_tail_call() helper") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit af50e4b ] syzbot caught an infinite recursion in nsh_gso_segment(). Problem here is that we need to make sure the NSH header is of reasonable length. BUG: MAX_LOCK_DEPTH too low! turning off the locking correctness validator. depth: 48 max: 48! 48 locks held by syz-executor0/10189: #0: (ptrval) (rcu_read_lock_bh){....}, at: __dev_queue_xmit+0x30f/0x34c0 net/core/dev.c:3517 #1: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #1: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #2: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #2: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #3: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #3: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #4: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #4: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #5: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #5: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #6: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #6: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #7: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #7: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #8: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #8: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #9: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #9: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #10: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #10: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #11: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #11: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #12: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #12: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #13: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #13: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #14: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #14: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #15: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #15: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #16: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #16: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #17: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #17: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #18: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #18: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #19: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #19: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #20: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #20: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #21: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #21: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #22: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #22: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #23: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #23: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #24: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #24: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #25: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #25: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #26: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #26: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #27: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #27: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #28: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #28: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #29: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #29: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #30: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #30: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #31: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #31: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 dccp_close: ABORT with 65423 bytes unread #32: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #32: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #33: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #33: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #34: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #34: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #35: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #35: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #36: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #36: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #37: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #37: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #38: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #38: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #39: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #39: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #40: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #40: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #41: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #41: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #42: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #42: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #43: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #43: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #44: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #44: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #45: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #45: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #46: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #46: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 #47: (ptrval) (rcu_read_lock){....}, at: __skb_pull include/linux/skbuff.h:2080 [inline] #47: (ptrval) (rcu_read_lock){....}, at: skb_mac_gso_segment+0x221/0x720 net/core/dev.c:2787 INFO: lockdep is turned off. CPU: 1 PID: 10189 Comm: syz-executor0 Not tainted 4.17.0-rc2+ #26 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1b9/0x294 lib/dump_stack.c:113 __lock_acquire+0x1788/0x5140 kernel/locking/lockdep.c:3449 lock_acquire+0x1dc/0x520 kernel/locking/lockdep.c:3920 rcu_lock_acquire include/linux/rcupdate.h:246 [inline] rcu_read_lock include/linux/rcupdate.h:632 [inline] skb_mac_gso_segment+0x25b/0x720 net/core/dev.c:2789 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 nsh_gso_segment+0x405/0xb60 net/nsh/nsh.c:107 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792 __skb_gso_segment+0x3bb/0x870 net/core/dev.c:2865 skb_gso_segment include/linux/netdevice.h:4025 [inline] validate_xmit_skb+0x54d/0xd90 net/core/dev.c:3118 validate_xmit_skb_list+0xbf/0x120 net/core/dev.c:3168 sch_direct_xmit+0x354/0x11e0 net/sched/sch_generic.c:312 qdisc_restart net/sched/sch_generic.c:399 [inline] __qdisc_run+0x741/0x1af0 net/sched/sch_generic.c:410 __dev_xmit_skb net/core/dev.c:3243 [inline] __dev_queue_xmit+0x28ea/0x34c0 net/core/dev.c:3551 dev_queue_xmit+0x17/0x20 net/core/dev.c:3616 packet_snd net/packet/af_packet.c:2951 [inline] packet_sendmsg+0x40f8/0x6070 net/packet/af_packet.c:2976 sock_sendmsg_nosec net/socket.c:629 [inline] sock_sendmsg+0xd5/0x120 net/socket.c:639 __sys_sendto+0x3d7/0x670 net/socket.c:1789 __do_sys_sendto net/socket.c:1801 [inline] __se_sys_sendto net/socket.c:1797 [inline] __x64_sys_sendto+0xe1/0x1a0 net/socket.c:1797 do_syscall_64+0x1b1/0x800 arch/x86/entry/common.c:287 entry_SYSCALL_64_after_hwframe+0x49/0xbe Fixes: c411ed8 ("nsh: add GSO support") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jiri Benc <jbenc@redhat.com> Reported-by: syzbot <syzkaller@googlegroups.com> Acked-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 755a8bf ] If someone has the silly idea to write something along those lines: extern u64 foo(void); void bar(struct arm_smccc_res *res) { arm_smccc_1_1_smc(0xbad, foo(), res); } they are in for a surprise, as this gets compiled as: 0000000000000588 <bar>: 588: a9be7bfd stp x29, x30, [sp, #-32]! 58c: 910003fd mov x29, sp 590: f9000bf3 str x19, [sp, #16] 594: aa0003f3 mov x19, x0 598: aa1e03e0 mov x0, x30 59c: 94000000 bl 0 <_mcount> 5a0: 94000000 bl 0 <foo> 5a4: aa0003e1 mov x1, x0 5a8: d4000003 smc #0x0 5ac: b4000073 cbz x19, 5b8 <bar+0x30> 5b0: a9000660 stp x0, x1, [x19] 5b4: a9010e62 stp x2, x3, [x19, #16] 5b8: f9400bf3 ldr x19, [sp, #16] 5bc: a8c27bfd ldp x29, x30, [sp], #32 5c0: d65f03c0 ret 5c4: d503201f nop The call to foo "overwrites" the x0 register for the return value, and we end up calling the wrong secure service. A solution is to evaluate all the parameters before assigning anything to specific registers, leading to the expected result: 0000000000000588 <bar>: 588: a9be7bfd stp x29, x30, [sp, #-32]! 58c: 910003fd mov x29, sp 590: f9000bf3 str x19, [sp, #16] 594: aa0003f3 mov x19, x0 598: aa1e03e0 mov x0, x30 59c: 94000000 bl 0 <_mcount> 5a0: 94000000 bl 0 <foo> 5a4: aa0003e1 mov x1, x0 5a8: d28175a0 mov x0, #0xbad 5ac: d4000003 smc #0x0 5b0: b4000073 cbz x19, 5bc <bar+0x34> 5b4: a9000660 stp x0, x1, [x19] 5b8: a9010e62 stp x2, x3, [x19, #16] 5bc: f9400bf3 ldr x19, [sp, #16] 5c0: a8c27bfd ldp x29, x30, [sp], #32 5c4: d65f03c0 ret Reported-by: Julien Grall <julien.grall@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 8601a99 ] When enable SMMU, remove HNS driver will cause a WARNING: [ 141.924177] WARNING: CPU: 36 PID: 2708 at drivers/iommu/dma-iommu.c:443 __iommu_dma_unmap+0xc0/0xc8 [ 141.954673] Modules linked in: hns_enet_drv(-) [ 141.963615] CPU: 36 PID: 2708 Comm: rmmod Tainted: G W 5.0.0-rc1-28723-gb729c57de95c-dirty #32 [ 141.983593] Hardware name: Huawei D05/D05, BIOS Hisilicon D05 UEFI Nemo 1.8 RC0 08/31/2017 [ 142.000244] pstate: 60000005 (nZCv daif -PAN -UAO) [ 142.009886] pc : __iommu_dma_unmap+0xc0/0xc8 [ 142.018476] lr : __iommu_dma_unmap+0xc0/0xc8 [ 142.027066] sp : ffff000013533b90 [ 142.033728] x29: ffff000013533b90 x28: ffff8013e6983600 [ 142.044420] x27: 0000000000000000 x26: 0000000000000000 [ 142.055113] x25: 0000000056000000 x24: 0000000000000015 [ 142.065806] x23: 0000000000000028 x22: ffff8013e66eee68 [ 142.076499] x21: ffff8013db919800 x20: 0000ffffefbff000 [ 142.087192] x19: 0000000000001000 x18: 0000000000000007 [ 142.097885] x17: 000000000000000e x16: 0000000000000001 [ 142.108578] x15: 0000000000000019 x14: 363139343a70616d [ 142.119270] x13: 6e75656761705f67 x12: 0000000000000000 [ 142.129963] x11: 00000000ffffffff x10: 0000000000000006 [ 142.140656] x9 : 1346c1aa88093500 x8 : ffff0000114de4e0 [ 142.151349] x7 : 6662666578303d72 x6 : ffff0000105ffec8 [ 142.162042] x5 : 0000000000000000 x4 : 0000000000000000 [ 142.172734] x3 : 00000000ffffffff x2 : ffff0000114de500 [ 142.183427] x1 : 0000000000000000 x0 : 0000000000000035 [ 142.194120] Call trace: [ 142.199030] __iommu_dma_unmap+0xc0/0xc8 [ 142.206920] iommu_dma_unmap_page+0x20/0x28 [ 142.215335] __iommu_unmap_page+0x40/0x60 [ 142.223399] hnae_unmap_buffer+0x110/0x134 [ 142.231639] hnae_free_desc+0x6c/0x10c [ 142.239177] hnae_fini_ring+0x14/0x34 [ 142.246540] hnae_fini_queue+0x2c/0x40 [ 142.254080] hnae_put_handle+0x38/0xcc [ 142.261619] hns_nic_dev_remove+0x54/0xfc [hns_enet_drv] [ 142.272312] platform_drv_remove+0x24/0x64 [ 142.280552] device_release_driver_internal+0x17c/0x20c [ 142.291070] driver_detach+0x4c/0x90 [ 142.298259] bus_remove_driver+0x5c/0xd8 [ 142.306148] driver_unregister+0x2c/0x54 [ 142.314037] platform_driver_unregister+0x10/0x18 [ 142.323505] hns_nic_dev_driver_exit+0x14/0xf0c [hns_enet_drv] [ 142.335248] __arm64_sys_delete_module+0x214/0x25c [ 142.344891] el0_svc_common+0xb0/0x10c [ 142.352430] el0_svc_handler+0x24/0x80 [ 142.359968] el0_svc+0x8/0x7c0 [ 142.366104] ---[ end trace 60ad1cd58e63c407 ]--- The tx ring buffer map when xmit and unmap when xmit done. So in hnae_init_ring() did not map tx ring buffer, but in hnae_fini_ring() have a unmap operation for tx ring buffer, which is already unmapped when xmit done, than cause this WARNING. The hnae_alloc_buffers() is called in hnae_init_ring(), so the hnae_free_buffers() should be in hnae_fini_ring(), not in hnae_free_desc(). In hnae_fini_ring(), adds a check is_rx_ring() as in hnae_init_ring(). When the ring buffer is tx ring, adds a piece of code to ensure that the tx ring is unmap. Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a4270d6 ] If a network driver provides to napi_gro_frags() an skb with a page fragment of exactly 14 bytes, the call to gro_pull_from_frag0() will 'consume' the fragment by calling skb_frag_unref(skb, 0), and the page might be freed and reused. Reading eth->h_proto at the end of napi_frags_skb() might read mangled data, or crash under specific debugging features. BUG: KASAN: use-after-free in napi_frags_skb net/core/dev.c:5833 [inline] BUG: KASAN: use-after-free in napi_gro_frags+0xc6f/0xd10 net/core/dev.c:5841 Read of size 2 at addr ffff88809366840c by task syz-executor599/8957 CPU: 1 PID: 8957 Comm: syz-executor599 Not tainted 5.2.0-rc1+ #32 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x172/0x1f0 lib/dump_stack.c:113 print_address_description.cold+0x7c/0x20d mm/kasan/report.c:188 __kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317 kasan_report+0x12/0x20 mm/kasan/common.c:614 __asan_report_load_n_noabort+0xf/0x20 mm/kasan/generic_report.c:142 napi_frags_skb net/core/dev.c:5833 [inline] napi_gro_frags+0xc6f/0xd10 net/core/dev.c:5841 tun_get_user+0x2f3c/0x3ff0 drivers/net/tun.c:1991 tun_chr_write_iter+0xbd/0x156 drivers/net/tun.c:2037 call_write_iter include/linux/fs.h:1872 [inline] do_iter_readv_writev+0x5f8/0x8f0 fs/read_write.c:693 do_iter_write fs/read_write.c:970 [inline] do_iter_write+0x184/0x610 fs/read_write.c:951 vfs_writev+0x1b3/0x2f0 fs/read_write.c:1015 do_writev+0x15b/0x330 fs/read_write.c:1058 Fixes: a50e233 ("net-gro: restore frag0 optimization") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit d4d5d8e ] Before thread in process context uses bh_lock_sock() we must disable bh. sysbot reported : WARNING: inconsistent lock state 5.2.0-rc3+ #32 Not tainted inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage. blkid/26581 [HC0[0]:SC1[1]:HE1:SE0] takes: 00000000e0da85ee (slock-AF_AX25){+.?.}, at: spin_lock include/linux/spinlock.h:338 [inline] 00000000e0da85ee (slock-AF_AX25){+.?.}, at: ax25_destroy_timer+0x53/0xc0 net/ax25/af_ax25.c:275 {SOFTIRQ-ON-W} state was registered at: lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:4303 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline] _raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:151 spin_lock include/linux/spinlock.h:338 [inline] ax25_rt_autobind+0x3ca/0x720 net/ax25/ax25_route.c:429 ax25_connect.cold+0x30/0xa4 net/ax25/af_ax25.c:1221 __sys_connect+0x264/0x330 net/socket.c:1834 __do_sys_connect net/socket.c:1845 [inline] __se_sys_connect net/socket.c:1842 [inline] __x64_sys_connect+0x73/0xb0 net/socket.c:1842 do_syscall_64+0xfd/0x680 arch/x86/entry/common.c:301 entry_SYSCALL_64_after_hwframe+0x49/0xbe irq event stamp: 2272 hardirqs last enabled at (2272): [<ffffffff810065f3>] trace_hardirqs_on_thunk+0x1a/0x1c hardirqs last disabled at (2271): [<ffffffff8100660f>] trace_hardirqs_off_thunk+0x1a/0x1c softirqs last enabled at (1522): [<ffffffff87400654>] __do_softirq+0x654/0x94c kernel/softirq.c:320 softirqs last disabled at (2267): [<ffffffff81449010>] invoke_softirq kernel/softirq.c:374 [inline] softirqs last disabled at (2267): [<ffffffff81449010>] irq_exit+0x180/0x1d0 kernel/softirq.c:414 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(slock-AF_AX25); <Interrupt> lock(slock-AF_AX25); *** DEADLOCK *** 1 lock held by blkid/26581: #0: 0000000010fd154d ((&ax25->dtimer)){+.-.}, at: lockdep_copy_map include/linux/lockdep.h:175 [inline] #0: 0000000010fd154d ((&ax25->dtimer)){+.-.}, at: call_timer_fn+0xe0/0x720 kernel/time/timer.c:1312 stack backtrace: CPU: 1 PID: 26581 Comm: blkid Not tainted 5.2.0-rc3+ #32 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x172/0x1f0 lib/dump_stack.c:113 print_usage_bug.cold+0x393/0x4a2 kernel/locking/lockdep.c:2935 valid_state kernel/locking/lockdep.c:2948 [inline] mark_lock_irq kernel/locking/lockdep.c:3138 [inline] mark_lock+0xd46/0x1370 kernel/locking/lockdep.c:3513 mark_irqflags kernel/locking/lockdep.c:3391 [inline] __lock_acquire+0x159f/0x5490 kernel/locking/lockdep.c:3745 lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:4303 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline] _raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:151 spin_lock include/linux/spinlock.h:338 [inline] ax25_destroy_timer+0x53/0xc0 net/ax25/af_ax25.c:275 call_timer_fn+0x193/0x720 kernel/time/timer.c:1322 expire_timers kernel/time/timer.c:1366 [inline] __run_timers kernel/time/timer.c:1685 [inline] __run_timers kernel/time/timer.c:1653 [inline] run_timer_softirq+0x66f/0x1740 kernel/time/timer.c:1698 __do_softirq+0x25c/0x94c kernel/softirq.c:293 invoke_softirq kernel/softirq.c:374 [inline] irq_exit+0x180/0x1d0 kernel/softirq.c:414 exiting_irq arch/x86/include/asm/apic.h:536 [inline] smp_apic_timer_interrupt+0x13b/0x550 arch/x86/kernel/apic/apic.c:1068 apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:806 </IRQ> RIP: 0033:0x7f858d5c3232 Code: 8b 61 08 48 8b 84 24 d8 00 00 00 4c 89 44 24 28 48 8b ac 24 d0 00 00 00 4c 8b b4 24 e8 00 00 00 48 89 7c 24 68 48 89 4c 24 78 <48> 89 44 24 58 8b 84 24 e0 00 00 00 89 84 24 84 00 00 00 8b 84 24 RSP: 002b:00007ffcaf0cf5c0 EFLAGS: 00000206 ORIG_RAX: ffffffffffffff13 RAX: 00007f858d7d27a8 RBX: 00007f858d7d8820 RCX: 00007f858d3940d8 RDX: 00007ffcaf0cf798 RSI: 00000000f5e616f3 RDI: 00007f858d394fee RBP: 0000000000000000 R08: 00007ffcaf0cf780 R09: 00007f858d7db480 R10: 0000000000000000 R11: 0000000009691a75 R12: 0000000000000005 R13: 00000000f5e616f3 R14: 0000000000000000 R15: 00007ffcaf0cf798 Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit f3e92cb ] Nine years ago, I added RCU handling to neighbours, not pneighbours. (pneigh are not commonly used) Unfortunately I missed that /proc dump operations would use a common entry and exit point : neigh_seq_start() and neigh_seq_stop() We need to read_lock(tbl->lock) or risk use-after-free while iterating the pneigh structures. We might later convert pneigh to RCU and revert this patch. sysbot reported : BUG: KASAN: use-after-free in pneigh_get_next.isra.0+0x24b/0x280 net/core/neighbour.c:3158 Read of size 8 at addr ffff888097f2a700 by task syz-executor.0/9825 CPU: 1 PID: 9825 Comm: syz-executor.0 Not tainted 5.2.0-rc4+ #32 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x172/0x1f0 lib/dump_stack.c:113 print_address_description.cold+0x7c/0x20d mm/kasan/report.c:188 __kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317 kasan_report+0x12/0x20 mm/kasan/common.c:614 __asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:132 pneigh_get_next.isra.0+0x24b/0x280 net/core/neighbour.c:3158 neigh_seq_next+0xdb/0x210 net/core/neighbour.c:3240 seq_read+0x9cf/0x1110 fs/seq_file.c:258 proc_reg_read+0x1fc/0x2c0 fs/proc/inode.c:221 do_loop_readv_writev fs/read_write.c:714 [inline] do_loop_readv_writev fs/read_write.c:701 [inline] do_iter_read+0x4a4/0x660 fs/read_write.c:935 vfs_readv+0xf0/0x160 fs/read_write.c:997 kernel_readv fs/splice.c:359 [inline] default_file_splice_read+0x475/0x890 fs/splice.c:414 do_splice_to+0x127/0x180 fs/splice.c:877 splice_direct_to_actor+0x2d2/0x970 fs/splice.c:954 do_splice_direct+0x1da/0x2a0 fs/splice.c:1063 do_sendfile+0x597/0xd00 fs/read_write.c:1464 __do_sys_sendfile64 fs/read_write.c:1525 [inline] __se_sys_sendfile64 fs/read_write.c:1511 [inline] __x64_sys_sendfile64+0x1dd/0x220 fs/read_write.c:1511 do_syscall_64+0xfd/0x680 arch/x86/entry/common.c:301 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x4592c9 Code: fd b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 cb b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007f4aab51dc78 EFLAGS: 00000246 ORIG_RAX: 0000000000000028 RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 00000000004592c9 RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000005 RBP: 000000000075bf20 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000080000000 R11: 0000000000000246 R12: 00007f4aab51e6d4 R13: 00000000004c689d R14: 00000000004db828 R15: 00000000ffffffff Allocated by task 9827: save_stack+0x23/0x90 mm/kasan/common.c:71 set_track mm/kasan/common.c:79 [inline] __kasan_kmalloc mm/kasan/common.c:489 [inline] __kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:462 kasan_kmalloc+0x9/0x10 mm/kasan/common.c:503 __do_kmalloc mm/slab.c:3660 [inline] __kmalloc+0x15c/0x740 mm/slab.c:3669 kmalloc include/linux/slab.h:552 [inline] pneigh_lookup+0x19c/0x4a0 net/core/neighbour.c:731 arp_req_set_public net/ipv4/arp.c:1010 [inline] arp_req_set+0x613/0x720 net/ipv4/arp.c:1026 arp_ioctl+0x652/0x7f0 net/ipv4/arp.c:1226 inet_ioctl+0x2a0/0x340 net/ipv4/af_inet.c:926 sock_do_ioctl+0xd8/0x2f0 net/socket.c:1043 sock_ioctl+0x3ed/0x780 net/socket.c:1194 vfs_ioctl fs/ioctl.c:46 [inline] file_ioctl fs/ioctl.c:509 [inline] do_vfs_ioctl+0xd5f/0x1380 fs/ioctl.c:696 ksys_ioctl+0xab/0xd0 fs/ioctl.c:713 __do_sys_ioctl fs/ioctl.c:720 [inline] __se_sys_ioctl fs/ioctl.c:718 [inline] __x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718 do_syscall_64+0xfd/0x680 arch/x86/entry/common.c:301 entry_SYSCALL_64_after_hwframe+0x49/0xbe Freed by task 9824: save_stack+0x23/0x90 mm/kasan/common.c:71 set_track mm/kasan/common.c:79 [inline] __kasan_slab_free+0x102/0x150 mm/kasan/common.c:451 kasan_slab_free+0xe/0x10 mm/kasan/common.c:459 __cache_free mm/slab.c:3432 [inline] kfree+0xcf/0x220 mm/slab.c:3755 pneigh_ifdown_and_unlock net/core/neighbour.c:812 [inline] __neigh_ifdown+0x236/0x2f0 net/core/neighbour.c:356 neigh_ifdown+0x20/0x30 net/core/neighbour.c:372 arp_ifdown+0x1d/0x21 net/ipv4/arp.c:1274 inetdev_destroy net/ipv4/devinet.c:319 [inline] inetdev_event+0xa14/0x11f0 net/ipv4/devinet.c:1544 notifier_call_chain+0xc2/0x230 kernel/notifier.c:95 __raw_notifier_call_chain kernel/notifier.c:396 [inline] raw_notifier_call_chain+0x2e/0x40 kernel/notifier.c:403 call_netdevice_notifiers_info+0x3f/0x90 net/core/dev.c:1749 call_netdevice_notifiers_extack net/core/dev.c:1761 [inline] call_netdevice_notifiers net/core/dev.c:1775 [inline] rollback_registered_many+0x9b9/0xfc0 net/core/dev.c:8178 rollback_registered+0x109/0x1d0 net/core/dev.c:8220 unregister_netdevice_queue net/core/dev.c:9267 [inline] unregister_netdevice_queue+0x1ee/0x2c0 net/core/dev.c:9260 unregister_netdevice include/linux/netdevice.h:2631 [inline] __tun_detach+0xd8a/0x1040 drivers/net/tun.c:724 tun_detach drivers/net/tun.c:741 [inline] tun_chr_close+0xe0/0x180 drivers/net/tun.c:3451 __fput+0x2ff/0x890 fs/file_table.c:280 ____fput+0x16/0x20 fs/file_table.c:313 task_work_run+0x145/0x1c0 kernel/task_work.c:113 tracehook_notify_resume include/linux/tracehook.h:185 [inline] exit_to_usermode_loop+0x273/0x2c0 arch/x86/entry/common.c:168 prepare_exit_to_usermode arch/x86/entry/common.c:199 [inline] syscall_return_slowpath arch/x86/entry/common.c:279 [inline] do_syscall_64+0x58e/0x680 arch/x86/entry/common.c:304 entry_SYSCALL_64_after_hwframe+0x49/0xbe The buggy address belongs to the object at ffff888097f2a700 which belongs to the cache kmalloc-64 of size 64 The buggy address is located 0 bytes inside of 64-byte region [ffff888097f2a700, ffff888097f2a740) The buggy address belongs to the page: page:ffffea00025fca80 refcount:1 mapcount:0 mapping:ffff8880aa400340 index:0x0 flags: 0x1fffc0000000200(slab) raw: 01fffc0000000200 ffffea000250d548 ffffea00025726c8 ffff8880aa400340 raw: 0000000000000000 ffff888097f2a000 0000000100000020 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff888097f2a600: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc ffff888097f2a680: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc >ffff888097f2a700: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ^ ffff888097f2a780: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ffff888097f2a800: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc Fixes: 767e97e ("neigh: RCU conversion of struct neighbour") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit d4d5d8e ] Before thread in process context uses bh_lock_sock() we must disable bh. sysbot reported : WARNING: inconsistent lock state 5.2.0-rc3+ #32 Not tainted inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage. blkid/26581 [HC0[0]:SC1[1]:HE1:SE0] takes: 00000000e0da85ee (slock-AF_AX25){+.?.}, at: spin_lock include/linux/spinlock.h:338 [inline] 00000000e0da85ee (slock-AF_AX25){+.?.}, at: ax25_destroy_timer+0x53/0xc0 net/ax25/af_ax25.c:275 {SOFTIRQ-ON-W} state was registered at: lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:4303 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline] _raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:151 spin_lock include/linux/spinlock.h:338 [inline] ax25_rt_autobind+0x3ca/0x720 net/ax25/ax25_route.c:429 ax25_connect.cold+0x30/0xa4 net/ax25/af_ax25.c:1221 __sys_connect+0x264/0x330 net/socket.c:1834 __do_sys_connect net/socket.c:1845 [inline] __se_sys_connect net/socket.c:1842 [inline] __x64_sys_connect+0x73/0xb0 net/socket.c:1842 do_syscall_64+0xfd/0x680 arch/x86/entry/common.c:301 entry_SYSCALL_64_after_hwframe+0x49/0xbe irq event stamp: 2272 hardirqs last enabled at (2272): [<ffffffff810065f3>] trace_hardirqs_on_thunk+0x1a/0x1c hardirqs last disabled at (2271): [<ffffffff8100660f>] trace_hardirqs_off_thunk+0x1a/0x1c softirqs last enabled at (1522): [<ffffffff87400654>] __do_softirq+0x654/0x94c kernel/softirq.c:320 softirqs last disabled at (2267): [<ffffffff81449010>] invoke_softirq kernel/softirq.c:374 [inline] softirqs last disabled at (2267): [<ffffffff81449010>] irq_exit+0x180/0x1d0 kernel/softirq.c:414 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(slock-AF_AX25); <Interrupt> lock(slock-AF_AX25); *** DEADLOCK *** 1 lock held by blkid/26581: #0: 0000000010fd154d ((&ax25->dtimer)){+.-.}, at: lockdep_copy_map include/linux/lockdep.h:175 [inline] #0: 0000000010fd154d ((&ax25->dtimer)){+.-.}, at: call_timer_fn+0xe0/0x720 kernel/time/timer.c:1312 stack backtrace: CPU: 1 PID: 26581 Comm: blkid Not tainted 5.2.0-rc3+ #32 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x172/0x1f0 lib/dump_stack.c:113 print_usage_bug.cold+0x393/0x4a2 kernel/locking/lockdep.c:2935 valid_state kernel/locking/lockdep.c:2948 [inline] mark_lock_irq kernel/locking/lockdep.c:3138 [inline] mark_lock+0xd46/0x1370 kernel/locking/lockdep.c:3513 mark_irqflags kernel/locking/lockdep.c:3391 [inline] __lock_acquire+0x159f/0x5490 kernel/locking/lockdep.c:3745 lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:4303 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline] _raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:151 spin_lock include/linux/spinlock.h:338 [inline] ax25_destroy_timer+0x53/0xc0 net/ax25/af_ax25.c:275 call_timer_fn+0x193/0x720 kernel/time/timer.c:1322 expire_timers kernel/time/timer.c:1366 [inline] __run_timers kernel/time/timer.c:1685 [inline] __run_timers kernel/time/timer.c:1653 [inline] run_timer_softirq+0x66f/0x1740 kernel/time/timer.c:1698 __do_softirq+0x25c/0x94c kernel/softirq.c:293 invoke_softirq kernel/softirq.c:374 [inline] irq_exit+0x180/0x1d0 kernel/softirq.c:414 exiting_irq arch/x86/include/asm/apic.h:536 [inline] smp_apic_timer_interrupt+0x13b/0x550 arch/x86/kernel/apic/apic.c:1068 apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:806 </IRQ> RIP: 0033:0x7f858d5c3232 Code: 8b 61 08 48 8b 84 24 d8 00 00 00 4c 89 44 24 28 48 8b ac 24 d0 00 00 00 4c 8b b4 24 e8 00 00 00 48 89 7c 24 68 48 89 4c 24 78 <48> 89 44 24 58 8b 84 24 e0 00 00 00 89 84 24 84 00 00 00 8b 84 24 RSP: 002b:00007ffcaf0cf5c0 EFLAGS: 00000206 ORIG_RAX: ffffffffffffff13 RAX: 00007f858d7d27a8 RBX: 00007f858d7d8820 RCX: 00007f858d3940d8 RDX: 00007ffcaf0cf798 RSI: 00000000f5e616f3 RDI: 00007f858d394fee RBP: 0000000000000000 R08: 00007ffcaf0cf780 R09: 00007f858d7db480 R10: 0000000000000000 R11: 0000000009691a75 R12: 0000000000000005 R13: 00000000f5e616f3 R14: 0000000000000000 R15: 00007ffcaf0cf798 Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit f3e92cb ] Nine years ago, I added RCU handling to neighbours, not pneighbours. (pneigh are not commonly used) Unfortunately I missed that /proc dump operations would use a common entry and exit point : neigh_seq_start() and neigh_seq_stop() We need to read_lock(tbl->lock) or risk use-after-free while iterating the pneigh structures. We might later convert pneigh to RCU and revert this patch. sysbot reported : BUG: KASAN: use-after-free in pneigh_get_next.isra.0+0x24b/0x280 net/core/neighbour.c:3158 Read of size 8 at addr ffff888097f2a700 by task syz-executor.0/9825 CPU: 1 PID: 9825 Comm: syz-executor.0 Not tainted 5.2.0-rc4+ #32 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x172/0x1f0 lib/dump_stack.c:113 print_address_description.cold+0x7c/0x20d mm/kasan/report.c:188 __kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317 kasan_report+0x12/0x20 mm/kasan/common.c:614 __asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:132 pneigh_get_next.isra.0+0x24b/0x280 net/core/neighbour.c:3158 neigh_seq_next+0xdb/0x210 net/core/neighbour.c:3240 seq_read+0x9cf/0x1110 fs/seq_file.c:258 proc_reg_read+0x1fc/0x2c0 fs/proc/inode.c:221 do_loop_readv_writev fs/read_write.c:714 [inline] do_loop_readv_writev fs/read_write.c:701 [inline] do_iter_read+0x4a4/0x660 fs/read_write.c:935 vfs_readv+0xf0/0x160 fs/read_write.c:997 kernel_readv fs/splice.c:359 [inline] default_file_splice_read+0x475/0x890 fs/splice.c:414 do_splice_to+0x127/0x180 fs/splice.c:877 splice_direct_to_actor+0x2d2/0x970 fs/splice.c:954 do_splice_direct+0x1da/0x2a0 fs/splice.c:1063 do_sendfile+0x597/0xd00 fs/read_write.c:1464 __do_sys_sendfile64 fs/read_write.c:1525 [inline] __se_sys_sendfile64 fs/read_write.c:1511 [inline] __x64_sys_sendfile64+0x1dd/0x220 fs/read_write.c:1511 do_syscall_64+0xfd/0x680 arch/x86/entry/common.c:301 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x4592c9 Code: fd b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 cb b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007f4aab51dc78 EFLAGS: 00000246 ORIG_RAX: 0000000000000028 RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 00000000004592c9 RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000005 RBP: 000000000075bf20 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000080000000 R11: 0000000000000246 R12: 00007f4aab51e6d4 R13: 00000000004c689d R14: 00000000004db828 R15: 00000000ffffffff Allocated by task 9827: save_stack+0x23/0x90 mm/kasan/common.c:71 set_track mm/kasan/common.c:79 [inline] __kasan_kmalloc mm/kasan/common.c:489 [inline] __kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:462 kasan_kmalloc+0x9/0x10 mm/kasan/common.c:503 __do_kmalloc mm/slab.c:3660 [inline] __kmalloc+0x15c/0x740 mm/slab.c:3669 kmalloc include/linux/slab.h:552 [inline] pneigh_lookup+0x19c/0x4a0 net/core/neighbour.c:731 arp_req_set_public net/ipv4/arp.c:1010 [inline] arp_req_set+0x613/0x720 net/ipv4/arp.c:1026 arp_ioctl+0x652/0x7f0 net/ipv4/arp.c:1226 inet_ioctl+0x2a0/0x340 net/ipv4/af_inet.c:926 sock_do_ioctl+0xd8/0x2f0 net/socket.c:1043 sock_ioctl+0x3ed/0x780 net/socket.c:1194 vfs_ioctl fs/ioctl.c:46 [inline] file_ioctl fs/ioctl.c:509 [inline] do_vfs_ioctl+0xd5f/0x1380 fs/ioctl.c:696 ksys_ioctl+0xab/0xd0 fs/ioctl.c:713 __do_sys_ioctl fs/ioctl.c:720 [inline] __se_sys_ioctl fs/ioctl.c:718 [inline] __x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718 do_syscall_64+0xfd/0x680 arch/x86/entry/common.c:301 entry_SYSCALL_64_after_hwframe+0x49/0xbe Freed by task 9824: save_stack+0x23/0x90 mm/kasan/common.c:71 set_track mm/kasan/common.c:79 [inline] __kasan_slab_free+0x102/0x150 mm/kasan/common.c:451 kasan_slab_free+0xe/0x10 mm/kasan/common.c:459 __cache_free mm/slab.c:3432 [inline] kfree+0xcf/0x220 mm/slab.c:3755 pneigh_ifdown_and_unlock net/core/neighbour.c:812 [inline] __neigh_ifdown+0x236/0x2f0 net/core/neighbour.c:356 neigh_ifdown+0x20/0x30 net/core/neighbour.c:372 arp_ifdown+0x1d/0x21 net/ipv4/arp.c:1274 inetdev_destroy net/ipv4/devinet.c:319 [inline] inetdev_event+0xa14/0x11f0 net/ipv4/devinet.c:1544 notifier_call_chain+0xc2/0x230 kernel/notifier.c:95 __raw_notifier_call_chain kernel/notifier.c:396 [inline] raw_notifier_call_chain+0x2e/0x40 kernel/notifier.c:403 call_netdevice_notifiers_info+0x3f/0x90 net/core/dev.c:1749 call_netdevice_notifiers_extack net/core/dev.c:1761 [inline] call_netdevice_notifiers net/core/dev.c:1775 [inline] rollback_registered_many+0x9b9/0xfc0 net/core/dev.c:8178 rollback_registered+0x109/0x1d0 net/core/dev.c:8220 unregister_netdevice_queue net/core/dev.c:9267 [inline] unregister_netdevice_queue+0x1ee/0x2c0 net/core/dev.c:9260 unregister_netdevice include/linux/netdevice.h:2631 [inline] __tun_detach+0xd8a/0x1040 drivers/net/tun.c:724 tun_detach drivers/net/tun.c:741 [inline] tun_chr_close+0xe0/0x180 drivers/net/tun.c:3451 __fput+0x2ff/0x890 fs/file_table.c:280 ____fput+0x16/0x20 fs/file_table.c:313 task_work_run+0x145/0x1c0 kernel/task_work.c:113 tracehook_notify_resume include/linux/tracehook.h:185 [inline] exit_to_usermode_loop+0x273/0x2c0 arch/x86/entry/common.c:168 prepare_exit_to_usermode arch/x86/entry/common.c:199 [inline] syscall_return_slowpath arch/x86/entry/common.c:279 [inline] do_syscall_64+0x58e/0x680 arch/x86/entry/common.c:304 entry_SYSCALL_64_after_hwframe+0x49/0xbe The buggy address belongs to the object at ffff888097f2a700 which belongs to the cache kmalloc-64 of size 64 The buggy address is located 0 bytes inside of 64-byte region [ffff888097f2a700, ffff888097f2a740) The buggy address belongs to the page: page:ffffea00025fca80 refcount:1 mapcount:0 mapping:ffff8880aa400340 index:0x0 flags: 0x1fffc0000000200(slab) raw: 01fffc0000000200 ffffea000250d548 ffffea00025726c8 ffff8880aa400340 raw: 0000000000000000 ffff888097f2a000 0000000100000020 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff888097f2a600: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc ffff888097f2a680: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc >ffff888097f2a700: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ^ ffff888097f2a780: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ffff888097f2a800: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc Fixes: 767e97e ("neigh: RCU conversion of struct neighbour") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a4270d6 upstream. If a network driver provides to napi_gro_frags() an skb with a page fragment of exactly 14 bytes, the call to gro_pull_from_frag0() will 'consume' the fragment by calling skb_frag_unref(skb, 0), and the page might be freed and reused. Reading eth->h_proto at the end of napi_frags_skb() might read mangled data, or crash under specific debugging features. BUG: KASAN: use-after-free in napi_frags_skb net/core/dev.c:5833 [inline] BUG: KASAN: use-after-free in napi_gro_frags+0xc6f/0xd10 net/core/dev.c:5841 Read of size 2 at addr ffff88809366840c by task syz-executor599/8957 CPU: 1 PID: 8957 Comm: syz-executor599 Not tainted 5.2.0-rc1+ #32 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x172/0x1f0 lib/dump_stack.c:113 print_address_description.cold+0x7c/0x20d mm/kasan/report.c:188 __kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317 kasan_report+0x12/0x20 mm/kasan/common.c:614 __asan_report_load_n_noabort+0xf/0x20 mm/kasan/generic_report.c:142 napi_frags_skb net/core/dev.c:5833 [inline] napi_gro_frags+0xc6f/0xd10 net/core/dev.c:5841 tun_get_user+0x2f3c/0x3ff0 drivers/net/tun.c:1991 tun_chr_write_iter+0xbd/0x156 drivers/net/tun.c:2037 call_write_iter include/linux/fs.h:1872 [inline] do_iter_readv_writev+0x5f8/0x8f0 fs/read_write.c:693 do_iter_write fs/read_write.c:970 [inline] do_iter_write+0x184/0x610 fs/read_write.c:951 vfs_writev+0x1b3/0x2f0 fs/read_write.c:1015 do_writev+0x15b/0x330 fs/read_write.c:1058 Fixes: a50e233 ("net-gro: restore frag0 optimization") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit f3e92cb upstream. Nine years ago, I added RCU handling to neighbours, not pneighbours. (pneigh are not commonly used) Unfortunately I missed that /proc dump operations would use a common entry and exit point : neigh_seq_start() and neigh_seq_stop() We need to read_lock(tbl->lock) or risk use-after-free while iterating the pneigh structures. We might later convert pneigh to RCU and revert this patch. sysbot reported : BUG: KASAN: use-after-free in pneigh_get_next.isra.0+0x24b/0x280 net/core/neighbour.c:3158 Read of size 8 at addr ffff888097f2a700 by task syz-executor.0/9825 CPU: 1 PID: 9825 Comm: syz-executor.0 Not tainted 5.2.0-rc4+ #32 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x172/0x1f0 lib/dump_stack.c:113 print_address_description.cold+0x7c/0x20d mm/kasan/report.c:188 __kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317 kasan_report+0x12/0x20 mm/kasan/common.c:614 __asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:132 pneigh_get_next.isra.0+0x24b/0x280 net/core/neighbour.c:3158 neigh_seq_next+0xdb/0x210 net/core/neighbour.c:3240 seq_read+0x9cf/0x1110 fs/seq_file.c:258 proc_reg_read+0x1fc/0x2c0 fs/proc/inode.c:221 do_loop_readv_writev fs/read_write.c:714 [inline] do_loop_readv_writev fs/read_write.c:701 [inline] do_iter_read+0x4a4/0x660 fs/read_write.c:935 vfs_readv+0xf0/0x160 fs/read_write.c:997 kernel_readv fs/splice.c:359 [inline] default_file_splice_read+0x475/0x890 fs/splice.c:414 do_splice_to+0x127/0x180 fs/splice.c:877 splice_direct_to_actor+0x2d2/0x970 fs/splice.c:954 do_splice_direct+0x1da/0x2a0 fs/splice.c:1063 do_sendfile+0x597/0xd00 fs/read_write.c:1464 __do_sys_sendfile64 fs/read_write.c:1525 [inline] __se_sys_sendfile64 fs/read_write.c:1511 [inline] __x64_sys_sendfile64+0x1dd/0x220 fs/read_write.c:1511 do_syscall_64+0xfd/0x680 arch/x86/entry/common.c:301 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x4592c9 Code: fd b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 cb b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007f4aab51dc78 EFLAGS: 00000246 ORIG_RAX: 0000000000000028 RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 00000000004592c9 RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000005 RBP: 000000000075bf20 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000080000000 R11: 0000000000000246 R12: 00007f4aab51e6d4 R13: 00000000004c689d R14: 00000000004db828 R15: 00000000ffffffff Allocated by task 9827: save_stack+0x23/0x90 mm/kasan/common.c:71 set_track mm/kasan/common.c:79 [inline] __kasan_kmalloc mm/kasan/common.c:489 [inline] __kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:462 kasan_kmalloc+0x9/0x10 mm/kasan/common.c:503 __do_kmalloc mm/slab.c:3660 [inline] __kmalloc+0x15c/0x740 mm/slab.c:3669 kmalloc include/linux/slab.h:552 [inline] pneigh_lookup+0x19c/0x4a0 net/core/neighbour.c:731 arp_req_set_public net/ipv4/arp.c:1010 [inline] arp_req_set+0x613/0x720 net/ipv4/arp.c:1026 arp_ioctl+0x652/0x7f0 net/ipv4/arp.c:1226 inet_ioctl+0x2a0/0x340 net/ipv4/af_inet.c:926 sock_do_ioctl+0xd8/0x2f0 net/socket.c:1043 sock_ioctl+0x3ed/0x780 net/socket.c:1194 vfs_ioctl fs/ioctl.c:46 [inline] file_ioctl fs/ioctl.c:509 [inline] do_vfs_ioctl+0xd5f/0x1380 fs/ioctl.c:696 ksys_ioctl+0xab/0xd0 fs/ioctl.c:713 __do_sys_ioctl fs/ioctl.c:720 [inline] __se_sys_ioctl fs/ioctl.c:718 [inline] __x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718 do_syscall_64+0xfd/0x680 arch/x86/entry/common.c:301 entry_SYSCALL_64_after_hwframe+0x49/0xbe Freed by task 9824: save_stack+0x23/0x90 mm/kasan/common.c:71 set_track mm/kasan/common.c:79 [inline] __kasan_slab_free+0x102/0x150 mm/kasan/common.c:451 kasan_slab_free+0xe/0x10 mm/kasan/common.c:459 __cache_free mm/slab.c:3432 [inline] kfree+0xcf/0x220 mm/slab.c:3755 pneigh_ifdown_and_unlock net/core/neighbour.c:812 [inline] __neigh_ifdown+0x236/0x2f0 net/core/neighbour.c:356 neigh_ifdown+0x20/0x30 net/core/neighbour.c:372 arp_ifdown+0x1d/0x21 net/ipv4/arp.c:1274 inetdev_destroy net/ipv4/devinet.c:319 [inline] inetdev_event+0xa14/0x11f0 net/ipv4/devinet.c:1544 notifier_call_chain+0xc2/0x230 kernel/notifier.c:95 __raw_notifier_call_chain kernel/notifier.c:396 [inline] raw_notifier_call_chain+0x2e/0x40 kernel/notifier.c:403 call_netdevice_notifiers_info+0x3f/0x90 net/core/dev.c:1749 call_netdevice_notifiers_extack net/core/dev.c:1761 [inline] call_netdevice_notifiers net/core/dev.c:1775 [inline] rollback_registered_many+0x9b9/0xfc0 net/core/dev.c:8178 rollback_registered+0x109/0x1d0 net/core/dev.c:8220 unregister_netdevice_queue net/core/dev.c:9267 [inline] unregister_netdevice_queue+0x1ee/0x2c0 net/core/dev.c:9260 unregister_netdevice include/linux/netdevice.h:2631 [inline] __tun_detach+0xd8a/0x1040 drivers/net/tun.c:724 tun_detach drivers/net/tun.c:741 [inline] tun_chr_close+0xe0/0x180 drivers/net/tun.c:3451 __fput+0x2ff/0x890 fs/file_table.c:280 ____fput+0x16/0x20 fs/file_table.c:313 task_work_run+0x145/0x1c0 kernel/task_work.c:113 tracehook_notify_resume include/linux/tracehook.h:185 [inline] exit_to_usermode_loop+0x273/0x2c0 arch/x86/entry/common.c:168 prepare_exit_to_usermode arch/x86/entry/common.c:199 [inline] syscall_return_slowpath arch/x86/entry/common.c:279 [inline] do_syscall_64+0x58e/0x680 arch/x86/entry/common.c:304 entry_SYSCALL_64_after_hwframe+0x49/0xbe The buggy address belongs to the object at ffff888097f2a700 which belongs to the cache kmalloc-64 of size 64 The buggy address is located 0 bytes inside of 64-byte region [ffff888097f2a700, ffff888097f2a740) The buggy address belongs to the page: page:ffffea00025fca80 refcount:1 mapcount:0 mapping:ffff8880aa400340 index:0x0 flags: 0x1fffc0000000200(slab) raw: 01fffc0000000200 ffffea000250d548 ffffea00025726c8 ffff8880aa400340 raw: 0000000000000000 ffff888097f2a000 0000000100000020 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff888097f2a600: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc ffff888097f2a680: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc >ffff888097f2a700: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ^ ffff888097f2a780: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ffff888097f2a800: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc Fixes: 767e97e ("neigh: RCU conversion of struct neighbour") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

… delivery commit 2464cc4 upstream. After a treclaim, we expect to be in non-transactional state. If we don't clear the current thread's MSR[TS] before we get preempted, then tm_recheckpoint_new_task() will recheckpoint and we get rescheduled in suspended transaction state. When handling a signal caught in transactional state, handle_rt_signal64() calls get_tm_stackpointer() that treclaims the transaction using tm_reclaim_current() but without clearing the thread's MSR[TS]. This can cause the TM Bad Thing exception below if later we pagefault and get preempted trying to access the user's sigframe, using __put_user(). Afterwards, when we are rescheduled back into do_page_fault() (but now in suspended state since the thread's MSR[TS] was not cleared), upon executing 'rfid' after completion of the page fault handling, the exception is raised because a transition from suspended to non-transactional state is invalid. Unexpected TM Bad Thing exception at c00000000000de44 (msr 0x8000000302a03031) tm_scratch=800000010280b033 Oops: Unrecoverable exception, sig: 6 [#1] LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries CPU: 25 PID: 15547 Comm: a.out Not tainted 5.4.0-rc2 #32 NIP: c00000000000de44 LR: c000000000034728 CTR: 0000000000000000 REGS: c00000003fe7bd70 TRAP: 0700 Not tainted (5.4.0-rc2) MSR: 8000000302a03031 <SF,VEC,VSX,FP,ME,IR,DR,LE,TM[SE]> CR: 44000884 XER: 00000000 CFAR: c00000000000dda4 IRQMASK: 0 PACATMSCRATCH: 800000010280b033 GPR00: c000000000034728 c000000f65a17c80 c000000001662800 00007fffacf3fd78 GPR04: 0000000000001000 0000000000001000 0000000000000000 c000000f611f8af0 GPR08: 0000000000000000 0000000078006001 0000000000000000 000c000000000000 GPR12: c000000f611f84b0 c00000003ffcb200 0000000000000000 0000000000000000 GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 GPR20: 0000000000000000 0000000000000000 0000000000000000 c000000f611f8140 GPR24: 0000000000000000 00007fffacf3fd68 c000000f65a17d90 c000000f611f7800 GPR28: c000000f65a17e90 c000000f65a17e90 c000000001685e18 00007fffacf3f000 NIP [c00000000000de44] fast_exception_return+0xf4/0x1b0 LR [c000000000034728] handle_rt_signal64+0x78/0xc50 Call Trace: [c000000f65a17c80] [c000000000034710] handle_rt_signal64+0x60/0xc50 (unreliable) [c000000f65a17d30] [c000000000023640] do_notify_resume+0x330/0x460 [c000000f65a17e20] [c00000000000dcc4] ret_from_except_lite+0x70/0x74 Instruction dump: 7c4ff120 e8410170 7c5a03a6 38400000 f8410060 e8010070 e8410080 e8610088 60000000 60000000 e8810090 e8210078 <4c000024> 48000000 e8610178 88ed0989 ---[ end trace 93094aa44b442f87 ]--- The simplified sequence of events that triggers the above exception is: ... # userspace in NON-TRANSACTIONAL state tbegin # userspace in TRANSACTIONAL state signal delivery # kernelspace in SUSPENDED state handle_rt_signal64() get_tm_stackpointer() treclaim # kernelspace in NON-TRANSACTIONAL state __put_user() page fault happens. We will never get back here because of the TM Bad Thing exception. page fault handling kicks in and we voluntarily preempt ourselves do_page_fault() __schedule() __switch_to(other_task) our task is rescheduled and we recheckpoint because the thread's MSR[TS] was not cleared __switch_to(our_task) switch_to_tm() tm_recheckpoint_new_task() trechkpt # kernelspace in SUSPENDED state The page fault handling resumes, but now we are in suspended transaction state do_page_fault() completes rfid <----- trying to get back where the page fault happened (we were non-transactional back then) TM Bad Thing # illegal transition from suspended to non-transactional This patch fixes that issue by clearing the current thread's MSR[TS] just after treclaim in get_tm_stackpointer() so that we stay in non-transactional state in case we are preempted. In order to make treclaim and clearing the thread's MSR[TS] atomic from a preemption perspective when CONFIG_PREEMPT is set, preempt_disable/enable() is used. It's also necessary to save the previous value of the thread's MSR before get_tm_stackpointer() is called so that it can be exposed to the signal handler later in setup_tm_sigcontexts() to inform the userspace MSR at the moment of the signal delivery. Found with tm-signal-context-force-tm kernel selftest. Fixes: 2b0a576 ("powerpc: Add new transactional memory state to the signal context") Cc: stable@vger.kernel.org # v3.9 Signed-off-by: Gustavo Luiz Duarte <gustavold@linux.ibm.com> Acked-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200211033831.11165-1-gustavold@linux.ibm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 96298f6 ] According to Core Spec Version 5.2 | Vol 3, Part A 6.1.5, the incoming L2CAP_ConfigReq should be handled during OPEN state. The section below shows the btmon trace when running L2CAP/COS/CFD/BV-12-C before and after this change. === Before === ... > ACL Data RX: Handle 256 flags 0x02 dlen 12 #22 L2CAP: Connection Request (0x02) ident 2 len 4 PSM: 1 (0x0001) Source CID: 65 < ACL Data TX: Handle 256 flags 0x00 dlen 16 #23 L2CAP: Connection Response (0x03) ident 2 len 8 Destination CID: 64 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 256 flags 0x00 dlen 12 #24 L2CAP: Configure Request (0x04) ident 2 len 4 Destination CID: 65 Flags: 0x0000 > HCI Event: Number of Completed Packets (0x13) plen 5 #25 Num handles: 1 Handle: 256 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 #26 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 16 #27 L2CAP: Configure Request (0x04) ident 3 len 8 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 .. < ACL Data TX: Handle 256 flags 0x00 dlen 18 #28 L2CAP: Configure Response (0x05) ident 3 len 10 Source CID: 65 Flags: 0x0000 Result: Success (0x0000) Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 672 > HCI Event: Number of Completed Packets (0x13) plen 5 #29 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 14 #30 L2CAP: Configure Response (0x05) ident 2 len 6 Source CID: 64 Flags: 0x0000 Result: Success (0x0000) > ACL Data RX: Handle 256 flags 0x02 dlen 20 #31 L2CAP: Configure Request (0x04) ident 3 len 12 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 91 02 11 11 ...... < ACL Data TX: Handle 256 flags 0x00 dlen 14 #32 L2CAP: Command Reject (0x01) ident 3 len 6 Reason: Invalid CID in request (0x0002) Destination CID: 64 Source CID: 65 > HCI Event: Number of Completed Packets (0x13) plen 5 #33 Num handles: 1 Handle: 256 Count: 1 ... === After === ... > ACL Data RX: Handle 256 flags 0x02 dlen 12 #22 L2CAP: Connection Request (0x02) ident 2 len 4 PSM: 1 (0x0001) Source CID: 65 < ACL Data TX: Handle 256 flags 0x00 dlen 16 #23 L2CAP: Connection Response (0x03) ident 2 len 8 Destination CID: 64 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 256 flags 0x00 dlen 12 #24 L2CAP: Configure Request (0x04) ident 2 len 4 Destination CID: 65 Flags: 0x0000 > HCI Event: Number of Completed Packets (0x13) plen 5 #25 Num handles: 1 Handle: 256 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 #26 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 16 #27 L2CAP: Configure Request (0x04) ident 3 len 8 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 .. < ACL Data TX: Handle 256 flags 0x00 dlen 18 #28 L2CAP: Configure Response (0x05) ident 3 len 10 Source CID: 65 Flags: 0x0000 Result: Success (0x0000) Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 672 > HCI Event: Number of Completed Packets (0x13) plen 5 #29 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 14 #30 L2CAP: Configure Response (0x05) ident 2 len 6 Source CID: 64 Flags: 0x0000 Result: Success (0x0000) > ACL Data RX: Handle 256 flags 0x02 dlen 20 #31 L2CAP: Configure Request (0x04) ident 3 len 12 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 91 02 11 11 ..... < ACL Data TX: Handle 256 flags 0x00 dlen 18 #32 L2CAP: Configure Response (0x05) ident 3 len 10 Source CID: 65 Flags: 0x0000 Result: Success (0x0000) Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 672 < ACL Data TX: Handle 256 flags 0x00 dlen 12 #33 L2CAP: Configure Request (0x04) ident 3 len 4 Destination CID: 65 Flags: 0x0000 > HCI Event: Number of Completed Packets (0x13) plen 5 #34 Num handles: 1 Handle: 256 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 #35 Num handles: 1 Handle: 256 Count: 1 ... Signed-off-by: Howard Chung <howardchung@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ee53437 ] Rafael reports that on a system with LX2160A and Marvell DSA switches, if a reboot occurs while the DSA master (dpaa2-eth) is up, the following panic can be seen: systemd-shutdown[1]: Rebooting. Unable to handle kernel paging request at virtual address 00a0000800000041 [00a0000800000041] address between user and kernel address ranges Internal error: Oops: 96000004 [hardkernel#1] PREEMPT SMP CPU: 6 PID: 1 Comm: systemd-shutdow Not tainted 5.16.5-00042-g8f5585009b24 hardkernel#32 pc : dsa_slave_netdevice_event+0x130/0x3e4 lr : raw_notifier_call_chain+0x50/0x6c Call trace: dsa_slave_netdevice_event+0x130/0x3e4 raw_notifier_call_chain+0x50/0x6c call_netdevice_notifiers_info+0x54/0xa0 __dev_close_many+0x50/0x130 dev_close_many+0x84/0x120 unregister_netdevice_many+0x130/0x710 unregister_netdevice_queue+0x8c/0xd0 unregister_netdev+0x20/0x30 dpaa2_eth_remove+0x68/0x190 fsl_mc_driver_remove+0x20/0x5c __device_release_driver+0x21c/0x220 device_release_driver_internal+0xac/0xb0 device_links_unbind_consumers+0xd4/0x100 __device_release_driver+0x94/0x220 device_release_driver+0x28/0x40 bus_remove_device+0x118/0x124 device_del+0x174/0x420 fsl_mc_device_remove+0x24/0x40 __fsl_mc_device_remove+0xc/0x20 device_for_each_child+0x58/0xa0 dprc_remove+0x90/0xb0 fsl_mc_driver_remove+0x20/0x5c __device_release_driver+0x21c/0x220 device_release_driver+0x28/0x40 bus_remove_device+0x118/0x124 device_del+0x174/0x420 fsl_mc_bus_remove+0x80/0x100 fsl_mc_bus_shutdown+0xc/0x1c platform_shutdown+0x20/0x30 device_shutdown+0x154/0x330 __do_sys_reboot+0x1cc/0x250 __arm64_sys_reboot+0x20/0x30 invoke_syscall.constprop.0+0x4c/0xe0 do_el0_svc+0x4c/0x150 el0_svc+0x24/0xb0 el0t_64_sync_handler+0xa8/0xb0 el0t_64_sync+0x178/0x17c It can be seen from the stack trace that the problem is that the deregistration of the master causes a dev_close(), which gets notified as NETDEV_GOING_DOWN to dsa_slave_netdevice_event(). But dsa_switch_shutdown() has already run, and this has unregistered the DSA slave interfaces, and yet, the NETDEV_GOING_DOWN handler attempts to call dev_close_many() on those slave interfaces, leading to the problem. The previous attempt to avoid the NETDEV_GOING_DOWN on the master after dsa_switch_shutdown() was called seems improper. Unregistering the slave interfaces is unnecessary and unhelpful. Instead, after the slaves have stopped being uppers of the DSA master, we can now reset to NULL the master->dsa_ptr pointer, which will make DSA start ignoring all future notifier events on the master. Fixes: 0650bf5 ("net: dsa: be compatible with masters which unregister on shutdown") Reported-by: Rafael Richter <rafael.richter@gin.de> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit bcd7026 ] By keep sending L2CAP_CONF_REQ packets, chan->num_conf_rsp increases multiple times and eventually it will wrap around the maximum number (i.e., 255). This patch prevents this by adding a boundary check with L2CAP_MAX_CONF_RSP Btmon log: Bluetooth monitor ver 5.64 = Note: Linux version 6.1.0-rc2 (x86_64) 0.264594 = Note: Bluetooth subsystem version 2.22 0.264636 @ MGMT Open: btmon (privileged) version 1.22 {0x0001} 0.272191 = New Index: 00:00:00:00:00:00 (Primary,Virtual,hci0) [hci0] 13.877604 @ RAW Open: 9496 (privileged) version 2.22 {0x0002} 13.890741 = Open Index: 00:00:00:00:00:00 [hci0] 13.900426 (...) > ACL Data RX: Handle 200 flags 0x00 dlen 1033 #32 [hci0] 14.273106 invalid packet size (12 != 1033) 08 00 01 00 02 01 04 00 01 10 ff ff ............ > ACL Data RX: Handle 200 flags 0x00 dlen 1547 #33 [hci0] 14.273561 invalid packet size (14 != 1547) 0a 00 01 00 04 01 06 00 40 00 00 00 00 00 ........@..... > ACL Data RX: Handle 200 flags 0x00 dlen 2061 #34 [hci0] 14.274390 invalid packet size (16 != 2061) 0c 00 01 00 04 01 08 00 40 00 00 00 00 00 00 04 ........@....... > ACL Data RX: Handle 200 flags 0x00 dlen 2061 #35 [hci0] 14.274932 invalid packet size (16 != 2061) 0c 00 01 00 04 01 08 00 40 00 00 00 07 00 03 00 ........@....... = bluetoothd: Bluetooth daemon 5.43 14.401828 > ACL Data RX: Handle 200 flags 0x00 dlen 1033 #36 [hci0] 14.275753 invalid packet size (12 != 1033) 08 00 01 00 04 01 04 00 40 00 00 00 ........@... Signed-off-by: Sungwoo Kim <iam@sung-woo.kim> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d055368 ] The conclusion "j1939_session_deactivate() should be called with a session ref-count of at least 2" is incorrect. In some concurrent scenarios, j1939_session_deactivate can be called with the session ref-count less than 2. But there is not any problem because it will check the session active state before session putting in j1939_session_deactivate_locked(). Here is the concurrent scenario of the problem reported by syzbot and my reproduction log. cpu0 cpu1 j1939_xtp_rx_eoma j1939_xtp_rx_abort_one j1939_session_get_by_addr [kref == 2] j1939_session_get_by_addr [kref == 3] j1939_session_deactivate [kref == 2] j1939_session_put [kref == 1] j1939_session_completed j1939_session_deactivate WARN_ON_ONCE(kref < 2) ===================================================== WARNING: CPU: 1 PID: 21 at net/can/j1939/transport.c:1088 j1939_session_deactivate+0x5f/0x70 CPU: 1 PID: 21 Comm: ksoftirqd/1 Not tainted 5.14.0-rc7+ #32 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1 04/01/2014 RIP: 0010:j1939_session_deactivate+0x5f/0x70 Call Trace: j1939_session_deactivate_activate_next+0x11/0x28 j1939_xtp_rx_eoma+0x12a/0x180 j1939_tp_recv+0x4a2/0x510 j1939_can_recv+0x226/0x380 can_rcv_filter+0xf8/0x220 can_receive+0x102/0x220 ? process_backlog+0xf0/0x2c0 can_rcv+0x53/0xf0 __netif_receive_skb_one_core+0x67/0x90 ? process_backlog+0x97/0x2c0 __netif_receive_skb+0x22/0x80 Fixes: 0c71437 ("can: j1939: j1939_session_deactivate(): clarify lifetime of session object") Reported-by: syzbot+9981a614060dcee6eeca@syzkaller.appspotmail.com Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Link: https://lore.kernel.org/all/20210906094200.95868-1-william.xuanziyang@huawei.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit bcd7026 ] By keep sending L2CAP_CONF_REQ packets, chan->num_conf_rsp increases multiple times and eventually it will wrap around the maximum number (i.e., 255). This patch prevents this by adding a boundary check with L2CAP_MAX_CONF_RSP Btmon log: Bluetooth monitor ver 5.64 = Note: Linux version 6.1.0-rc2 (x86_64) 0.264594 = Note: Bluetooth subsystem version 2.22 0.264636 @ MGMT Open: btmon (privileged) version 1.22 {0x0001} 0.272191 = New Index: 00:00:00:00:00:00 (Primary,Virtual,hci0) [hci0] 13.877604 @ RAW Open: 9496 (privileged) version 2.22 {0x0002} 13.890741 = Open Index: 00:00:00:00:00:00 [hci0] 13.900426 (...) > ACL Data RX: Handle 200 flags 0x00 dlen 1033 #32 [hci0] 14.273106 invalid packet size (12 != 1033) 08 00 01 00 02 01 04 00 01 10 ff ff ............ > ACL Data RX: Handle 200 flags 0x00 dlen 1547 #33 [hci0] 14.273561 invalid packet size (14 != 1547) 0a 00 01 00 04 01 06 00 40 00 00 00 00 00 ........@..... > ACL Data RX: Handle 200 flags 0x00 dlen 2061 #34 [hci0] 14.274390 invalid packet size (16 != 2061) 0c 00 01 00 04 01 08 00 40 00 00 00 00 00 00 04 ........@....... > ACL Data RX: Handle 200 flags 0x00 dlen 2061 #35 [hci0] 14.274932 invalid packet size (16 != 2061) 0c 00 01 00 04 01 08 00 40 00 00 00 07 00 03 00 ........@....... = bluetoothd: Bluetooth daemon 5.43 14.401828 > ACL Data RX: Handle 200 flags 0x00 dlen 1033 #36 [hci0] 14.275753 invalid packet size (12 != 1033) 08 00 01 00 04 01 04 00 40 00 00 00 ........@... Signed-off-by: Sungwoo Kim <iam@sung-woo.kim> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5ee0d47 ] Currently, when using non-blocking commits, we can see the following kernel warning: [ 110.908514] ------------[ cut here ]------------ [ 110.908529] refcount_t: underflow; use-after-free. [ 110.908620] WARNING: CPU: 0 PID: 1866 at lib/refcount.c:87 refcount_dec_not_one+0xb8/0xc0 [ 110.908664] Modules linked in: rfcomm snd_seq_dummy snd_hrtimer snd_seq snd_seq_device cmac algif_hash aes_arm64 aes_generic algif_skcipher af_alg bnep hid_logitech_hidpp vc4 brcmfmac hci_uart btbcm brcmutil bluetooth snd_soc_hdmi_codec cfg80211 cec drm_display_helper drm_dma_helper drm_kms_helper snd_soc_core snd_compress snd_pcm_dmaengine fb_sys_fops sysimgblt syscopyarea sysfillrect raspberrypi_hwmon ecdh_generic ecc rfkill libaes i2c_bcm2835 binfmt_misc joydev snd_bcm2835(C) bcm2835_codec(C) bcm2835_isp(C) v4l2_mem2mem videobuf2_dma_contig snd_pcm bcm2835_v4l2(C) raspberrypi_gpiomem bcm2835_mmal_vchiq(C) videobuf2_v4l2 snd_timer videobuf2_vmalloc videobuf2_memops videobuf2_common snd videodev vc_sm_cma(C) mc hid_logitech_dj uio_pdrv_genirq uio i2c_dev drm fuse dm_mod drm_panel_orientation_quirks backlight ip_tables x_tables ipv6 [ 110.909086] CPU: 0 PID: 1866 Comm: kodi.bin Tainted: G C 6.1.66-v8+ #32 [ 110.909104] Hardware name: Raspberry Pi 3 Model B Rev 1.2 (DT) [ 110.909114] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 110.909132] pc : refcount_dec_not_one+0xb8/0xc0 [ 110.909152] lr : refcount_dec_not_one+0xb4/0xc0 [ 110.909170] sp : ffffffc00913b9c0 [ 110.909177] x29: ffffffc00913b9c0 x28: 000000556969bbb0 x27: 000000556990df60 [ 110.909205] x26: 0000000000000002 x25: 0000000000000004 x24: ffffff8004448480 [ 110.909230] x23: ffffff800570b500 x22: ffffff802e03a7bc x21: ffffffecfca68c78 [ 110.909257] x20: ffffff8002b42000 x19: ffffff802e03a600 x18: 0000000000000000 [ 110.909283] x17: 0000000000000011 x16: ffffffffffffffff x15: 0000000000000004 [ 110.909308] x14: 0000000000000fff x13: ffffffed577e47e0 x12: 0000000000000003 [ 110.909333] x11: 0000000000000000 x10: 0000000000000027 x9 : c912d0d083728c00 [ 110.909359] x8 : c912d0d083728c00 x7 : 65646e75203a745f x6 : 746e756f63666572 [ 110.909384] x5 : ffffffed579f62ee x4 : ffffffed579eb01e x3 : 0000000000000000 [ 110.909409] x2 : 0000000000000000 x1 : ffffffc00913b750 x0 : 0000000000000001 [ 110.909434] Call trace: [ 110.909441] refcount_dec_not_one+0xb8/0xc0 [ 110.909461] vc4_bo_dec_usecnt+0x4c/0x1b0 [vc4] [ 110.909903] vc4_cleanup_fb+0x44/0x50 [vc4] [ 110.910315] drm_atomic_helper_cleanup_planes+0x88/0xa4 [drm_kms_helper] [ 110.910669] vc4_atomic_commit_tail+0x390/0x9dc [vc4] [ 110.911079] commit_tail+0xb0/0x164 [drm_kms_helper] [ 110.911397] drm_atomic_helper_commit+0x1d0/0x1f0 [drm_kms_helper] [ 110.911716] drm_atomic_commit+0xb0/0xdc [drm] [ 110.912569] drm_mode_atomic_ioctl+0x348/0x4b8 [drm] [ 110.913330] drm_ioctl_kernel+0xec/0x15c [drm] [ 110.914091] drm_ioctl+0x24c/0x3b0 [drm] [ 110.914850] __arm64_sys_ioctl+0x9c/0xd4 [ 110.914873] invoke_syscall+0x4c/0x114 [ 110.914897] el0_svc_common+0xd0/0x118 [ 110.914917] do_el0_svc+0x38/0xd0 [ 110.914936] el0_svc+0x30/0x8c [ 110.914958] el0t_64_sync_handler+0x84/0xf0 [ 110.914979] el0t_64_sync+0x18c/0x190 [ 110.914996] ---[ end trace 0000000000000000 ]--- This happens because, although `prepare_fb` and `cleanup_fb` are perfectly balanced, we cannot guarantee consistency in the check plane->state->fb == state->fb. This means that sometimes we can increase the refcount in `prepare_fb` and don't decrease it in `cleanup_fb`. The opposite can also be true. In fact, the struct drm_plane .state shouldn't be accessed directly but instead, the `drm_atomic_get_new_plane_state()` helper function should be used. So, we could stick to this check, but using `drm_atomic_get_new_plane_state()`. But actually, this check is not really needed. We can increase and decrease the refcount symmetrically without problems. This is going to make the code more simple and consistent. Signed-off-by: Maíra Canal <mcanal@igalia.com> Acked-by: Maxime Ripard <mripard@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240105175908.242000-1-mcanal@igalia.com Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 61cf1c7 ] KMSAN reported uninit-value access in raw_lookup() [1]. Diag for raw sockets uses the pad field in struct inet_diag_req_v2 for the underlying protocol. This field corresponds to the sdiag_raw_protocol field in struct inet_diag_req_raw. inet_diag_get_exact_compat() converts inet_diag_req to inet_diag_req_v2, but leaves the pad field uninitialized. So the issue occurs when raw_lookup() accesses the sdiag_raw_protocol field. Fix this by initializing the pad field in inet_diag_get_exact_compat(). Also, do the same fix in inet_diag_dump_compat() to avoid the similar issue in the future. [1] BUG: KMSAN: uninit-value in raw_lookup net/ipv4/raw_diag.c:49 [inline] BUG: KMSAN: uninit-value in raw_sock_get+0x657/0x800 net/ipv4/raw_diag.c:71 raw_lookup net/ipv4/raw_diag.c:49 [inline] raw_sock_get+0x657/0x800 net/ipv4/raw_diag.c:71 raw_diag_dump_one+0xa1/0x660 net/ipv4/raw_diag.c:99 inet_diag_cmd_exact+0x7d9/0x980 inet_diag_get_exact_compat net/ipv4/inet_diag.c:1404 [inline] inet_diag_rcv_msg_compat+0x469/0x530 net/ipv4/inet_diag.c:1426 sock_diag_rcv_msg+0x23d/0x740 net/core/sock_diag.c:282 netlink_rcv_skb+0x537/0x670 net/netlink/af_netlink.c:2564 sock_diag_rcv+0x35/0x40 net/core/sock_diag.c:297 netlink_unicast_kernel net/netlink/af_netlink.c:1335 [inline] netlink_unicast+0xe74/0x1240 net/netlink/af_netlink.c:1361 netlink_sendmsg+0x10c6/0x1260 net/netlink/af_netlink.c:1905 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x332/0x3d0 net/socket.c:745 ____sys_sendmsg+0x7f0/0xb70 net/socket.c:2585 ___sys_sendmsg+0x271/0x3b0 net/socket.c:2639 __sys_sendmsg net/socket.c:2668 [inline] __do_sys_sendmsg net/socket.c:2677 [inline] __se_sys_sendmsg net/socket.c:2675 [inline] __x64_sys_sendmsg+0x27e/0x4a0 net/socket.c:2675 x64_sys_call+0x135e/0x3ce0 arch/x86/include/generated/asm/syscalls_64.h:47 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xd9/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Uninit was stored to memory at: raw_sock_get+0x650/0x800 net/ipv4/raw_diag.c:71 raw_diag_dump_one+0xa1/0x660 net/ipv4/raw_diag.c:99 inet_diag_cmd_exact+0x7d9/0x980 inet_diag_get_exact_compat net/ipv4/inet_diag.c:1404 [inline] inet_diag_rcv_msg_compat+0x469/0x530 net/ipv4/inet_diag.c:1426 sock_diag_rcv_msg+0x23d/0x740 net/core/sock_diag.c:282 netlink_rcv_skb+0x537/0x670 net/netlink/af_netlink.c:2564 sock_diag_rcv+0x35/0x40 net/core/sock_diag.c:297 netlink_unicast_kernel net/netlink/af_netlink.c:1335 [inline] netlink_unicast+0xe74/0x1240 net/netlink/af_netlink.c:1361 netlink_sendmsg+0x10c6/0x1260 net/netlink/af_netlink.c:1905 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x332/0x3d0 net/socket.c:745 ____sys_sendmsg+0x7f0/0xb70 net/socket.c:2585 ___sys_sendmsg+0x271/0x3b0 net/socket.c:2639 __sys_sendmsg net/socket.c:2668 [inline] __do_sys_sendmsg net/socket.c:2677 [inline] __se_sys_sendmsg net/socket.c:2675 [inline] __x64_sys_sendmsg+0x27e/0x4a0 net/socket.c:2675 x64_sys_call+0x135e/0x3ce0 arch/x86/include/generated/asm/syscalls_64.h:47 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xd9/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Local variable req.i created at: inet_diag_get_exact_compat net/ipv4/inet_diag.c:1396 [inline] inet_diag_rcv_msg_compat+0x2a6/0x530 net/ipv4/inet_diag.c:1426 sock_diag_rcv_msg+0x23d/0x740 net/core/sock_diag.c:282 CPU: 1 PID: 8888 Comm: syz-executor.6 Not tainted 6.10.0-rc4-00217-g35bb670d65fc #32 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014 Fixes: 432490f ("net: ip, diag -- Add diag interface for raw sockets") Reported-by: syzkaller <syzkaller@googlegroups.com> Signed-off-by: Shigeru Yoshida <syoshida@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://patch.msgid.link/20240703091649.111773-1-syoshida@redhat.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 3802f73 upstream. blk_mq_clear_flush_rq_mapping() is not called during scsi probe, by checking blk_queue_init_done(). However, QUEUE_FLAG_INIT_DONE is cleared in del_gendisk by commit aec89dc ("block: keep q_usage_counter in atomic mode after del_gendisk"), hence for disk like scsi, following blk_mq_destroy_queue() will not clear flush rq from tags->rqs[] as well, cause following uaf that is found by our syzkaller for v6.6: ================================================================== BUG: KASAN: slab-use-after-free in blk_mq_find_and_get_req+0x16e/0x1a0 block/blk-mq-tag.c:261 Read of size 4 at addr ffff88811c969c20 by task kworker/1:2H/224909 CPU: 1 PID: 224909 Comm: kworker/1:2H Not tainted 6.6.0-ga836a5060850 #32 Workqueue: kblockd blk_mq_timeout_work Call Trace: __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x91/0xf0 lib/dump_stack.c:106 print_address_description.constprop.0+0x66/0x300 mm/kasan/report.c:364 print_report+0x3e/0x70 mm/kasan/report.c:475 kasan_report+0xb8/0xf0 mm/kasan/report.c:588 blk_mq_find_and_get_req+0x16e/0x1a0 block/blk-mq-tag.c:261 bt_iter block/blk-mq-tag.c:288 [inline] __sbitmap_for_each_set include/linux/sbitmap.h:295 [inline] sbitmap_for_each_set include/linux/sbitmap.h:316 [inline] bt_for_each+0x455/0x790 block/blk-mq-tag.c:325 blk_mq_queue_tag_busy_iter+0x320/0x740 block/blk-mq-tag.c:534 blk_mq_timeout_work+0x1a3/0x7b0 block/blk-mq.c:1673 process_one_work+0x7c4/0x1450 kernel/workqueue.c:2631 process_scheduled_works kernel/workqueue.c:2704 [inline] worker_thread+0x804/0xe40 kernel/workqueue.c:2785 kthread+0x346/0x450 kernel/kthread.c:388 ret_from_fork+0x4d/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1b/0x30 arch/x86/entry/entry_64.S:293 Allocated by task 942: kasan_save_stack+0x22/0x50 mm/kasan/common.c:45 kasan_set_track+0x25/0x30 mm/kasan/common.c:52 ____kasan_kmalloc mm/kasan/common.c:374 [inline] __kasan_kmalloc mm/kasan/common.c:383 [inline] __kasan_kmalloc+0xaa/0xb0 mm/kasan/common.c:380 kasan_kmalloc include/linux/kasan.h:198 [inline] __do_kmalloc_node mm/slab_common.c:1007 [inline] __kmalloc_node+0x69/0x170 mm/slab_common.c:1014 kmalloc_node include/linux/slab.h:620 [inline] kzalloc_node include/linux/slab.h:732 [inline] blk_alloc_flush_queue+0x144/0x2f0 block/blk-flush.c:499 blk_mq_alloc_hctx+0x601/0x940 block/blk-mq.c:3788 blk_mq_alloc_and_init_hctx+0x27f/0x330 block/blk-mq.c:4261 blk_mq_realloc_hw_ctxs+0x488/0x5e0 block/blk-mq.c:4294 blk_mq_init_allocated_queue+0x188/0x860 block/blk-mq.c:4350 blk_mq_init_queue_data block/blk-mq.c:4166 [inline] blk_mq_init_queue+0x8d/0x100 block/blk-mq.c:4176 scsi_alloc_sdev+0x843/0xd50 drivers/scsi/scsi_scan.c:335 scsi_probe_and_add_lun+0x77c/0xde0 drivers/scsi/scsi_scan.c:1189 __scsi_scan_target+0x1fc/0x5a0 drivers/scsi/scsi_scan.c:1727 scsi_scan_channel drivers/scsi/scsi_scan.c:1815 [inline] scsi_scan_channel+0x14b/0x1e0 drivers/scsi/scsi_scan.c:1791 scsi_scan_host_selected+0x2fe/0x400 drivers/scsi/scsi_scan.c:1844 scsi_scan+0x3a0/0x3f0 drivers/scsi/scsi_sysfs.c:151 store_scan+0x2a/0x60 drivers/scsi/scsi_sysfs.c:191 dev_attr_store+0x5c/0x90 drivers/base/core.c:2388 sysfs_kf_write+0x11c/0x170 fs/sysfs/file.c:136 kernfs_fop_write_iter+0x3fc/0x610 fs/kernfs/file.c:338 call_write_iter include/linux/fs.h:2083 [inline] new_sync_write+0x1b4/0x2d0 fs/read_write.c:493 vfs_write+0x76c/0xb00 fs/read_write.c:586 ksys_write+0x127/0x250 fs/read_write.c:639 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x70/0x120 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x78/0xe2 Freed by task 244687: kasan_save_stack+0x22/0x50 mm/kasan/common.c:45 kasan_set_track+0x25/0x30 mm/kasan/common.c:52 kasan_save_free_info+0x2b/0x50 mm/kasan/generic.c:522 ____kasan_slab_free mm/kasan/common.c:236 [inline] __kasan_slab_free+0x12a/0x1b0 mm/kasan/common.c:244 kasan_slab_free include/linux/kasan.h:164 [inline] slab_free_hook mm/slub.c:1815 [inline] slab_free_freelist_hook mm/slub.c:1841 [inline] slab_free mm/slub.c:3807 [inline] __kmem_cache_free+0xe4/0x520 mm/slub.c:3820 blk_free_flush_queue+0x40/0x60 block/blk-flush.c:520 blk_mq_hw_sysfs_release+0x4a/0x170 block/blk-mq-sysfs.c:37 kobject_cleanup+0x136/0x410 lib/kobject.c:689 kobject_release lib/kobject.c:720 [inline] kref_put include/linux/kref.h:65 [inline] kobject_put+0x119/0x140 lib/kobject.c:737 blk_mq_release+0x24f/0x3f0 block/blk-mq.c:4144 blk_free_queue block/blk-core.c:298 [inline] blk_put_queue+0xe2/0x180 block/blk-core.c:314 blkg_free_workfn+0x376/0x6e0 block/blk-cgroup.c:144 process_one_work+0x7c4/0x1450 kernel/workqueue.c:2631 process_scheduled_works kernel/workqueue.c:2704 [inline] worker_thread+0x804/0xe40 kernel/workqueue.c:2785 kthread+0x346/0x450 kernel/kthread.c:388 ret_from_fork+0x4d/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1b/0x30 arch/x86/entry/entry_64.S:293 Other than blk_mq_clear_flush_rq_mapping(), the flag is only used in blk_register_queue() from initialization path, hence it's safe not to clear the flag in del_gendisk. And since QUEUE_FLAG_REGISTERED already make sure that queue should only be registered once, there is no need to test the flag as well. Fixes: 6cfeadb ("blk-mq: don't clear flush_rq from tags->rqs[]") Depends-on: commit aec89dc ("block: keep q_usage_counter in atomic mode after del_gendisk") Signed-off-by: Yu Kuai <yukuai3@huawei.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Link: https://lore.kernel.org/r/20241104110005.1412161-1-yukuai1@huaweicloud.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: BRUNO VERNAY <bruno.vernay@se.com> Signed-off-by: Hugo SIMELIERE <hsimeliere.opensource@witekio.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 927fa5b upstream. KMSAN reported uninit-value access in __unix_walk_scc() [1]. In the list_for_each_entry_reverse() loop, when the vertex's index equals it's scc_index, the loop uses the variable vertex as a temporary variable that points to a vertex in scc. And when the loop is finished, the variable vertex points to the list head, in this case scc, which is a local variable on the stack (more precisely, it's not even scc and might underflow the call stack of __unix_walk_scc(): container_of(&scc, struct unix_vertex, scc_entry)). However, the variable vertex is used under the label prev_vertex. So if the edge_stack is not empty and the function jumps to the prev_vertex label, the function will access invalid data on the stack. This causes the uninit-value access issue. Fix this by introducing a new temporary variable for the loop. [1] BUG: KMSAN: uninit-value in __unix_walk_scc net/unix/garbage.c:478 [inline] BUG: KMSAN: uninit-value in unix_walk_scc net/unix/garbage.c:526 [inline] BUG: KMSAN: uninit-value in __unix_gc+0x2589/0x3c20 net/unix/garbage.c:584 __unix_walk_scc net/unix/garbage.c:478 [inline] unix_walk_scc net/unix/garbage.c:526 [inline] __unix_gc+0x2589/0x3c20 net/unix/garbage.c:584 process_one_work kernel/workqueue.c:3231 [inline] process_scheduled_works+0xade/0x1bf0 kernel/workqueue.c:3312 worker_thread+0xeb6/0x15b0 kernel/workqueue.c:3393 kthread+0x3c4/0x530 kernel/kthread.c:389 ret_from_fork+0x6e/0x90 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 Uninit was stored to memory at: unix_walk_scc net/unix/garbage.c:526 [inline] __unix_gc+0x2adf/0x3c20 net/unix/garbage.c:584 process_one_work kernel/workqueue.c:3231 [inline] process_scheduled_works+0xade/0x1bf0 kernel/workqueue.c:3312 worker_thread+0xeb6/0x15b0 kernel/workqueue.c:3393 kthread+0x3c4/0x530 kernel/kthread.c:389 ret_from_fork+0x6e/0x90 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 Local variable entries created at: ref_tracker_free+0x48/0xf30 lib/ref_tracker.c:222 netdev_tracker_free include/linux/netdevice.h:4058 [inline] netdev_put include/linux/netdevice.h:4075 [inline] dev_put include/linux/netdevice.h:4101 [inline] update_gid_event_work_handler+0xaa/0x1b0 drivers/infiniband/core/roce_gid_mgmt.c:813 CPU: 1 PID: 12763 Comm: kworker/u8:31 Not tainted 6.10.0-rc4-00217-g35bb670d65fc #32 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014 Workqueue: events_unbound __unix_gc Fixes: 3484f06 ("af_unix: Detect Strongly Connected Components.") Reported-by: syzkaller <syzkaller@googlegroups.com> Signed-off-by: Shigeru Yoshida <syoshida@redhat.com> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://patch.msgid.link/20240702160428.10153-1-syoshida@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When a userspace process that is not the drm master calls drm_mode_getconnector(), fill_modes() will not be called and connector mode list will not be updated. If mode list is not cleared when hdmi plug out, mode list obtained by the use-space process when hdmi is disconnected will still be the same as when hdmi is connected. This is inconsistent with the actual situation. So when the hdmi plug out, connector mode list needs to be actively cleared. The "modetest -c" printed when the error occurs is as follows: Connectors: id encoder status name size (mm) modes encoders 410 409 disconnected HDMI-A-1 0x0 49 409 modes: index name refresh (Hz) hdisp hss hse htot vdisp vss vse vtot #0 3840x2160 24.00 3840 4092 4180 5500 2160 2168 2178 2250 297000 flags: phsync, pvsync; type: preferred, driver #1 4096x2160 60.00 4096 4184 4272 4400 2160 2168 2178 2250 594000 flags: phsync, pvsync; type: driver #2 4096x2160 59.94 4096 4184 4272 4400 2160 2168 2178 2250 593407 flags: phsync, pvsync; type: driver #3 4096x2160 50.00 4096 5064 5152 5280 2160 2168 2178 2250 594000 flags: phsync, pvsync; type: driver #4 4096x2160 30.00 4096 4184 4272 4400 2160 2168 2178 2250 297000 flags: phsync, pvsync; type: driver #5 4096x2160 29.97 4096 4184 4272 4400 2160 2168 2178 2250 296703 flags: phsync, pvsync; type: driver #6 4096x2160 24.00 4096 5116 5204 5500 2160 2168 2178 2250 297000 flags: phsync, pvsync; type: driver #7 4096x2160 23.98 4096 5116 5204 5500 2160 2168 2178 2250 296703 flags: phsync, pvsync; type: driver #8 3840x2160 120.00 3840 4016 4104 4400 2160 2168 2178 2250 1188000 flags: phsync, pvsync; type: driver #9 3840x2160 119.88 3840 4016 4104 4400 2160 2168 2178 2250 1186813 flags: phsync, pvsync; type: driver #10 3840x2160 100.00 3840 4896 4984 5280 2160 2168 2178 2250 1188000 flags: phsync, pvsync; type: driver #11 3840x2160 60.00 3840 4016 4104 4400 2160 2168 2178 2250 594000 flags: phsync, pvsync; type: driver #12 3840x2160 59.94 3840 4016 4104 4400 2160 2168 2178 2250 593407 flags: phsync, pvsync; type: driver #13 3840x2160 50.00 3840 4896 4984 5280 2160 2168 2178 2250 594000 flags: phsync, pvsync; type: driver #14 3840x2160 30.00 3840 4016 4104 4400 2160 2168 2178 2250 297000 flags: phsync, pvsync; type: driver #15 3840x2160 29.97 3840 4016 4104 4400 2160 2168 2178 2250 296703 flags: phsync, pvsync; type: driver #16 3840x2160 25.00 3840 4896 4984 5280 2160 2168 2178 2250 297000 flags: phsync, pvsync; type: driver #17 3840x2160 24.00 3840 5116 5204 5500 2160 2168 2178 2250 297000 flags: phsync, pvsync; type: driver #18 3840x2160 23.98 3840 5116 5204 5500 2160 2168 2178 2250 296703 flags: phsync, pvsync; type: driver #19 1920x1080 120.00 1920 2008 2052 2200 1080 1084 1089 1125 297000 flags: phsync, pvsync; type: driver #20 1920x1080 119.88 1920 2008 2052 2200 1080 1084 1089 1125 296703 flags: phsync, pvsync; type: driver #21 1920x1080 60.00 1920 2008 2052 2200 1080 1084 1089 1125 148500 flags: phsync, pvsync; type: driver #22 1920x1080 60.00 1920 2008 2052 2200 1080 1084 1089 1125 148500 flags: phsync, pvsync; type: driver #23 1920x1080 59.94 1920 2008 2052 2200 1080 1084 1089 1125 148352 flags: phsync, pvsync; type: driver #24 1920x1080i 30.00 1920 2008 2052 2200 1080 1084 1094 1125 74250 flags: phsync, pvsync, interlace; type: driver #25 1920x1080i 29.97 1920 2008 2052 2200 1080 1084 1094 1125 74176 flags: phsync, pvsync, interlace; type: driver #26 1920x1080 50.00 1920 2448 2492 2640 1080 1084 1089 1125 148500 flags: phsync, pvsync; type: driver #27 1920x1080i 25.00 1920 2448 2492 2640 1080 1084 1094 1125 74250 flags: phsync, pvsync, interlace; type: driver #28 1920x1080 30.00 1920 2008 2052 2200 1080 1084 1089 1125 74250 flags: phsync, pvsync; type: driver #29 1920x1080 29.97 1920 2008 2052 2200 1080 1084 1089 1125 74176 flags: phsync, pvsync; type: driver #30 1920x1080 24.00 1920 2558 2602 2750 1080 1084 1089 1125 74250 flags: phsync, pvsync; type: driver #31 1920x1080 23.98 1920 2558 2602 2750 1080 1084 1089 1125 74176 flags: phsync, pvsync; type: driver #32 1280x1024 60.02 1280 1328 1440 1688 1024 1025 1028 1066 108000 flags: phsync, pvsync; type: driver #33 1280x800 59.91 1280 1328 1360 1440 800 803 809 823 71000 flags: phsync, nvsync; type: driver #34 1280x720 60.00 1280 1390 1430 1650 720 725 730 750 74250 flags: phsync, pvsync; type: driver #35 1280x720 60.00 1280 1390 1430 1650 720 725 730 750 74250 flags: phsync, pvsync; type: driver #36 1280x720 59.94 1280 1390 1430 1650 720 725 730 750 74176 flags: phsync, pvsync; type: driver #37 1280x720 50.00 1280 1720 1760 1980 720 725 730 750 74250 flags: phsync, pvsync; type: driver #38 1024x768 119.99 1024 1072 1104 1184 768 771 775 813 115500 flags: phsync, nvsync; type: driver #39 1024x768 60.00 1024 1048 1184 1344 768 771 777 806 65000 flags: nhsync, nvsync; type: driver #40 800x600 60.32 800 840 968 1056 600 601 605 628 40000 flags: phsync, pvsync; type: driver #41 720x576 50.00 720 732 796 864 576 581 586 625 27000 flags: nhsync, nvsync; type: driver #42 720x576 50.00 720 732 796 864 576 581 586 625 27000 flags: nhsync, nvsync; type: driver #43 720x480 60.00 720 736 798 858 480 489 495 525 27027 flags: nhsync, nvsync; type: driver #44 720x480 60.00 720 736 798 858 480 489 495 525 27027 flags: nhsync, nvsync; type: driver #45 720x480 59.94 720 736 798 858 480 489 495 525 27000 flags: nhsync, nvsync; type: driver #46 720x480 59.94 720 736 798 858 480 489 495 525 27000 flags: nhsync, nvsync; type: driver #47 640x480 60.00 640 656 752 800 480 490 492 525 25200 flags: nhsync, nvsync; type: driver #48 640x480 59.94 640 656 752 800 480 490 492 525 25175 flags: nhsync, nvsync; type: driver props: 1 EDID: flags: immutable blob blobs: value: 2 DPMS: flags: enum enums: On=0 Standby=1 Suspend=2 Off=3 value: 0 Fixes: f1c83fa ("drm/bridge: synopsys: dw-hdmi-qp: Clear edid property when hdmi plug out") Change-Id: I76551a751dd7ebe1da440c38ca5186b1d2b74e93 Signed-off-by: Algea Cao <algea.cao@rock-chips.com>

new asix driver 1.9.0 seehttp://www.asix.com.tw/FrootAttach/driver/A…
c06c5fd
…X88179_178A_LINUX_DRIVER_v1.9.0_SOURCE.tar.bz2

mdrjr added a commit that referenced this pull request Jan 15, 2014
Merge pull request#32from megglos/odroidxu-3.4.y
e8622e9
new asix GBE driver 1.9.0

mdrjr merged commit e8622e9 into hardkernel:odroidxu-3.4.yJan 15, 2014

Navigation Menu

new asix GBE driver 1.9.0 - #32

new asix GBE driver 1.9.0#32
mdrjr merged 1 commit into
hardkernel:odroidxu-3.4.yfrom
megglos:odroidxu-3.4.y

megglos commented Jan 14, 2014

Uh oh!

Reviewers

Assignees

Labels

Projects

Milestone

Development

Uh oh!

2 participants

Conversation

megglos commented Jan 14, 2014

Uh oh!

Reviewers

Assignees

Labels

Projects

Milestone

Development

Uh oh!

2 participants